patch-2.4.22 linux-2.4.22/Documentation/arm/SA1100/CERF
Next file: linux-2.4.22/Documentation/cciss.txt
Previous file: linux-2.4.22/Documentation/Configure.help
Back to the patch index
Back to the overall index
- Lines: 53
- Date:
2003-08-25 04:44:39.000000000 -0700
- Orig file:
linux-2.4.21/Documentation/arm/SA1100/CERF
- Orig date:
2000-08-13 09:58:24.000000000 -0700
diff -urN linux-2.4.21/Documentation/arm/SA1100/CERF linux-2.4.22/Documentation/arm/SA1100/CERF
@@ -1,23 +1,28 @@
-The Intrinsyc CerfBoard is a StrongARM 1110-based computer on a board that measures
-approximately 2" square. It includes an Ethernet controller, an RS232-compatible serial port, a
-USB function port, and one CompactFlash+ slot on the back. Pictures can be found at the
+The Intrinsyc CerfBoard is a StrongARM 1110-based computer on a board
+that measures approximately 2" square. It includes an Ethernet
+controller, an RS232-compatible serial port, a USB function port, and
+one CompactFlash+ slot on the back. Pictures can be found at the
Intrinsyc website, http://www.intrinsyc.com.
-This document describes the support in the Linux kernel for the Intrinsyc CerfBoard as of
-version 2.4.0-test4-np1.
+This document describes the support in the Linux kernel for the
+Intrinsyc CerfBoard as of version 2.4.0-test4-np1.
Supported in this version:
- - CompactFlash+ slot (select PCMCIA in General Setup and any options that may be required)
- - Onboard Crystal CS8900 Ethernet controller (Cerf CS8900A support in Network Devices)
+ - CompactFlash+ slot (select PCMCIA in General Setup and any options
+ that may be required)
+ - Onboard Crystal CS8900 Ethernet controller (Cerf CS8900A support in
+ Network Devices)
- Serial ports with a serial console (hardcoded to 38400 8N1)
Not supported in this version (yet):
- LCD driver/touchscreen interface
- - UDC (a driver exists right now, but is unstable and slow and only works with the Linux USB)
+ - UDC (a driver exists right now, but is unstable and slow and only
+ works with the Linux USB)
-In order to get this kernel onto your Cerf, you need a server that runs both BOOTP and
-TFTP. Detailed instructions should have come with your evaluation kit on how to use the
-bootloader. This series of commands will suffice:
+In order to get this kernel onto your Cerf, you need a server that runs
+both BOOTP and TFTP. Detailed instructions should have come with your
+evaluation kit on how to use the bootloader. This series of commands
+will suffice:
make cerf_config
make xconfig
@@ -25,10 +30,9 @@
make zImage
cp arch/arm/boot/zImage <TFTP directory>
-The default config uses a 4MB RAM disk located at 0xc0500000 as root. Setting the board to
-mount root from a NFS partition works, too.
+The default config uses a 4MB RAM disk located at 0xc0500000 as root.
+Setting the board to mount root from a NFS partition works, too.
I-Gene Leong, Intrinsyc Software Inc.
ileong@intrinsyc.com
-
FUNET's LINUX-ADM group, linux-adm@nic.funet.fi
TCL-scripts by Sam Shen (who was at: slshen@lbl.gov)