patch-2.4.22 linux-2.4.22/drivers/sgi/char/sgiserial.h

Next file: linux-2.4.22/drivers/sgi/char/shmiq.c
Previous file: linux-2.4.22/drivers/sgi/char/sgiserial.c
Back to the patch index
Back to the overall index

diff -urN linux-2.4.21/drivers/sgi/char/sgiserial.h linux-2.4.22/drivers/sgi/char/sgiserial.h
@@ -1,451 +0,0 @@
-/* sgiserial.h: Definitions for the SGI Zilog85C30 serial driver.
- *
- * Copyright (C) 1996 David S. Miller (dm@engr.sgi.com)
- */
-#ifndef _SGI_SERIAL_H
-#define _SGI_SERIAL_H
-
-/* Just one channel */
-struct sgi_zschannel {
-#ifdef __MIPSEB__
-	volatile unsigned char unused0[3];
-	volatile unsigned char control;
-	volatile unsigned char unused1[3];
-	volatile unsigned char data;
-#else /* __MIPSEL__ */
-	volatile unsigned char control;
-	volatile unsigned char unused0[3];
-	volatile unsigned char data;
-	volatile unsigned char unused1[3];
-#endif
-};
-
-/* The address space layout for each zs chip.  Yes they are
- * backwards.
- */
-struct sgi_zslayout {
-	struct sgi_zschannel channelB;
-	struct sgi_zschannel channelA;
-};
-
-#define NUM_ZSREGS    16
-
-struct serial_struct {
-	int	type;
-	int	line;
-	int	port;
-	int	irq;
-	int	flags;
-	int	xmit_fifo_size;
-	int	custom_divisor;
-	int	baud_base;
-	unsigned short	close_delay;
-	char	reserved_char[2];
-	int	hub6;
-	unsigned short	closing_wait; /* time to wait before closing */
-	unsigned short	closing_wait2; /* no longer used... */
-	int	reserved[4];
-};
-
-/*
- * For the close wait times, 0 means wait forever for serial port to
- * flush its output.  65535 means don't wait at all.
- */
-#define ZILOG_CLOSING_WAIT_INF	0
-#define ZILOG_CLOSING_WAIT_NONE	65535
-
-/*
- * Definitions for ZILOG_struct (and serial_struct) flags field
- */
-#define ZILOG_HUP_NOTIFY 0x0001 /* Notify getty on hangups and closes
-				   on the callout port */
-#define ZILOG_FOURPORT  0x0002	/* Set OU1, OUT2 per AST Fourport settings */
-#define ZILOG_SAK	0x0004	/* Secure Attention Key (Orange book) */
-#define ZILOG_SPLIT_TERMIOS 0x0008 /* Separate termios for dialin/callout */
-
-#define ZILOG_SPD_MASK	0x0030
-#define ZILOG_SPD_HI	0x0010	/* Use 56000 instead of 38400 bps */
-
-#define ZILOG_SPD_VHI	0x0020  /* Use 115200 instead of 38400 bps */
-#define ZILOG_SPD_CUST	0x0030  /* Use user-specified divisor */
-
-#define ZILOG_SKIP_TEST	0x0040 /* Skip UART test during autoconfiguration */
-#define ZILOG_AUTO_IRQ  0x0080 /* Do automatic IRQ during autoconfiguration */
-#define ZILOG_SESSION_LOCKOUT 0x0100 /* Lock out cua opens based on session */
-#define ZILOG_PGRP_LOCKOUT    0x0200 /* Lock out cua opens based on pgrp */
-#define ZILOG_CALLOUT_NOHUP   0x0400 /* Don't do hangups for cua device */
-
-#define ZILOG_FLAGS	0x0FFF	/* Possible legal ZILOG flags */
-#define ZILOG_USR_MASK 0x0430	/* Legal flags that non-privileged
-				 * users can set or reset */
-
-/* Internal flags used only by kernel/chr_drv/serial.c */
-#define ZILOG_INITIALIZED	0x80000000 /* Serial port was initialized */
-#define ZILOG_CALLOUT_ACTIVE	0x40000000 /* Call out device is active */
-#define ZILOG_NORMAL_ACTIVE	0x20000000 /* Normal device is active */
-#define ZILOG_BOOT_AUTOCONF	0x10000000 /* Autoconfigure port on bootup */
-#define ZILOG_CLOSING		0x08000000 /* Serial port is closing */
-#define ZILOG_CTS_FLOW		0x04000000 /* Do CTS flow control */
-#define ZILOG_CHECK_CD		0x02000000 /* i.e., CLOCAL */
-
-/* Software state per channel */
-
-#ifdef __KERNEL__
-/*
- * This is our internal structure for each serial port's state.
- *
- * Many fields are paralleled by the structure used by the serial_struct
- * structure.
- *
- * For definitions of the flags field, see tty.h
- */
-
-struct sgi_serial {
-	struct sgi_serial *zs_next;       /* For IRQ servicing chain */
-	struct sgi_zschannel *zs_channel; /* Channel registers */
-	unsigned char read_reg_zero;
-
-	char soft_carrier;  /* Use soft carrier on this channel */
-	char cons_keyb;     /* Channel runs the keyboard */
-	char cons_mouse;    /* Channel runs the mouse */
-	char break_abort;   /* Is serial console in, so process brk/abrt */
-	char kgdb_channel;  /* Kgdb is running on this channel */
-	char is_cons;       /* Is this our console. */
-
-	/* We need to know the current clock divisor
-	 * to read the bps rate the chip has currently
-	 * loaded.
-	 */
-	unsigned char clk_divisor;  /* May be 1, 16, 32, or 64 */
-	int zs_baud;
-
-	/* Current write register values */
-	unsigned char curregs[NUM_ZSREGS];
-
-	/* Values we need to set next opportunity */
-	unsigned char pendregs[NUM_ZSREGS];
-
-	char change_needed;
-
-	int			magic;
-	int			baud_base;
-	int			port;
-	int			irq;
-	int			flags; 		/* defined in tty.h */
-	int			type; 		/* UART type */
-	struct tty_struct 	*tty;
-	int			read_status_mask;
-	int			ignore_status_mask;
-	int			timeout;
-	int			xmit_fifo_size;
-	int			custom_divisor;
-	int			x_char;	/* xon/xoff character */
-	int			close_delay;
-	unsigned short		closing_wait;
-	unsigned short		closing_wait2;
-	unsigned long		event;
-	unsigned long		last_active;
-	int			line;
-	int			count;	    /* # of fd on device */
-	int			blocked_open; /* # of blocked opens */
-	long			session; /* Session of opening process */
-	long			pgrp; /* pgrp of opening process */
-	unsigned char 		*xmit_buf;
-	int			xmit_head;
-	int			xmit_tail;
-	int			xmit_cnt;
-	struct tq_struct	tqueue;
-	struct tq_struct	tqueue_hangup;
-	struct termios		normal_termios;
-	struct termios		callout_termios;
-	wait_queue_head_t	open_wait;
-	wait_queue_head_t	close_wait;
-};
-
-
-#define SERIAL_MAGIC 0x5301
-
-/*
- * The size of the serial xmit buffer is 1 page, or 4096 bytes
- */
-#define SERIAL_XMIT_SIZE 4096
-
-/*
- * Events are used to schedule things to happen at timer-interrupt
- * time, instead of at rs interrupt time.
- */
-#define RS_EVENT_WRITE_WAKEUP	0
-
-#endif /* __KERNEL__ */
-
-/* Conversion routines to/from brg time constants from/to bits
- * per second.
- */
-#define BRG_TO_BPS(brg, freq) ((freq) / 2 / ((brg) + 2))
-#define BPS_TO_BRG(bps, freq) ((((freq) + (bps)) / (2 * (bps))) - 2)
-
-/* The Zilog register set */
-
-#define	FLAG	0x7e
-
-/* Write Register 0 */
-#define	R0	0		/* Register selects */
-#define	R1	1
-#define	R2	2
-#define	R3	3
-#define	R4	4
-#define	R5	5
-#define	R6	6
-#define	R7	7
-#define	R8	8
-#define	R9	9
-#define	R10	10
-#define	R11	11
-#define	R12	12
-#define	R13	13
-#define	R14	14
-#define	R15	15
-
-#define	NULLCODE	0	/* Null Code */
-#define	POINT_HIGH	0x8	/* Select upper half of registers */
-#define	RES_EXT_INT	0x10	/* Reset Ext. Status Interrupts */
-#define	SEND_ABORT	0x18	/* HDLC Abort */
-#define	RES_RxINT_FC	0x20	/* Reset RxINT on First Character */
-#define	RES_Tx_P	0x28	/* Reset TxINT Pending */
-#define	ERR_RES		0x30	/* Error Reset */
-#define	RES_H_IUS	0x38	/* Reset highest IUS */
-
-#define	RES_Rx_CRC	0x40	/* Reset Rx CRC Checker */
-#define	RES_Tx_CRC	0x80	/* Reset Tx CRC Checker */
-#define	RES_EOM_L	0xC0	/* Reset EOM latch */
-
-/* Write Register 1 */
-
-#define	EXT_INT_ENAB	0x1	/* Ext Int Enable */
-#define	TxINT_ENAB	0x2	/* Tx Int Enable */
-#define	PAR_SPEC	0x4	/* Parity is special condition */
-
-#define	RxINT_DISAB	0	/* Rx Int Disable */
-#define	RxINT_FCERR	0x8	/* Rx Int on First Character Only or Error */
-#define	INT_ALL_Rx	0x10	/* Int on all Rx Characters or error */
-#define	INT_ERR_Rx	0x18	/* Int on error only */
-
-#define	WT_RDY_RT	0x20	/* Wait/Ready on R/T */
-#define	WT_FN_RDYFN	0x40	/* Wait/FN/Ready FN */
-#define	WT_RDY_ENAB	0x80	/* Wait/Ready Enable */
-
-/* Write Register #2 (Interrupt Vector) */
-
-/* Write Register 3 */
-
-#define	RxENABLE	0x1	/* Rx Enable */
-#define	SYNC_L_INH	0x2	/* Sync Character Load Inhibit */
-#define	ADD_SM		0x4	/* Address Search Mode (SDLC) */
-#define	RxCRC_ENAB	0x8	/* Rx CRC Enable */
-#define	ENT_HM		0x10	/* Enter Hunt Mode */
-#define	AUTO_ENAB	0x20	/* Auto Enables */
-#define	Rx5		0x0	/* Rx 5 Bits/Character */
-#define	Rx7		0x40	/* Rx 7 Bits/Character */
-#define	Rx6		0x80	/* Rx 6 Bits/Character */
-#define	Rx8		0xc0	/* Rx 8 Bits/Character */
-
-/* Write Register 4 */
-
-#define	PAR_ENA		0x1	/* Parity Enable */
-#define	PAR_EVEN	0x2	/* Parity Even/Odd* */
-
-#define	SYNC_ENAB	0	/* Sync Modes Enable */
-#define	SB1		0x4	/* 1 stop bit/char */
-#define	SB15		0x8	/* 1.5 stop bits/char */
-#define	SB2		0xc	/* 2 stop bits/char */
-
-#define	MONSYNC		0	/* 8 Bit Sync character */
-#define	BISYNC		0x10	/* 16 bit sync character */
-#define	SDLC		0x20	/* SDLC Mode (01111110 Sync Flag) */
-#define	EXTSYNC		0x30	/* External Sync Mode */
-
-#define	X1CLK		0x0	/* x1 clock mode */
-#define	X16CLK		0x40	/* x16 clock mode */
-#define	X32CLK		0x80	/* x32 clock mode */
-#define	X64CLK		0xC0	/* x64 clock mode */
-
-/* Write Register 5 */
-
-#define	TxCRC_ENAB	0x1	/* Tx CRC Enable */
-#define	RTS		0x2	/* RTS */
-#define	SDLC_CRC	0x4	/* SDLC/CRC-16 */
-#define	TxENAB		0x8	/* Tx Enable */
-#define	SND_BRK		0x10	/* Send Break */
-#define	Tx5		0x0	/* Tx 5 bits (or less)/character */
-#define	Tx7		0x20	/* Tx 7 bits/character */
-#define	Tx6		0x40	/* Tx 6 bits/character */
-#define	Tx8		0x60	/* Tx 8 bits/character */
-#define	DTR		0x80	/* DTR */
-
-/* Write Register 6 (Sync bits 0-7/SDLC Address Field) */
-
-/* Write Register 7 (Sync bits 8-15/SDLC 01111110) */
-
-/* Write Register 8 (transmit buffer) */
-
-/* Write Register 9 (Master interrupt control) */
-#define	VIS	1	/* Vector Includes Status */
-#define	NV	2	/* No Vector */
-#define	DLC	4	/* Disable Lower Chain */
-#define	MIE	8	/* Master Interrupt Enable */
-#define	STATHI	0x10	/* Status high */
-#define	NORESET	0	/* No reset on write to R9 */
-#define	CHRB	0x40	/* Reset channel B */
-#define	CHRA	0x80	/* Reset channel A */
-#define	FHWRES	0xc0	/* Force hardware reset */
-
-/* Write Register 10 (misc control bits) */
-#define	BIT6	1	/* 6 bit/8bit sync */
-#define	LOOPMODE 2	/* SDLC Loop mode */
-#define	ABUNDER	4	/* Abort/flag on SDLC xmit underrun */
-#define	MARKIDLE 8	/* Mark/flag on idle */
-#define	GAOP	0x10	/* Go active on poll */
-#define	NRZ	0	/* NRZ mode */
-#define	NRZI	0x20	/* NRZI mode */
-#define	FM1	0x40	/* FM1 (transition = 1) */
-#define	FM0	0x60	/* FM0 (transition = 0) */
-#define	CRCPS	0x80	/* CRC Preset I/O */
-
-/* Write Register 11 (Clock Mode control) */
-#define	TRxCXT	0	/* TRxC = Xtal output */
-#define	TRxCTC	1	/* TRxC = Transmit clock */
-#define	TRxCBR	2	/* TRxC = BR Generator Output */
-#define	TRxCDP	3	/* TRxC = DPLL output */
-#define	TRxCOI	4	/* TRxC O/I */
-#define	TCRTxCP	0	/* Transmit clock = RTxC pin */
-#define	TCTRxCP	8	/* Transmit clock = TRxC pin */
-#define	TCBR	0x10	/* Transmit clock = BR Generator output */
-#define	TCDPLL	0x18	/* Transmit clock = DPLL output */
-#define	RCRTxCP	0	/* Receive clock = RTxC pin */
-#define	RCTRxCP	0x20	/* Receive clock = TRxC pin */
-#define	RCBR	0x40	/* Receive clock = BR Generator output */
-#define	RCDPLL	0x60	/* Receive clock = DPLL output */
-#define	RTxCX	0x80	/* RTxC Xtal/No Xtal */
-
-/* Write Register 12 (lower byte of baud rate generator time constant) */
-
-/* Write Register 13 (upper byte of baud rate generator time constant) */
-
-/* Write Register 14 (Misc control bits) */
-#define	BRENABL	1	/* Baud rate generator enable */
-#define	BRSRC	2	/* Baud rate generator source */
-#define	DTRREQ	4	/* DTR/Request function */
-#define	AUTOECHO 8	/* Auto Echo */
-#define	LOOPBAK	0x10	/* Local loopback */
-#define	SEARCH	0x20	/* Enter search mode */
-#define	RMC	0x40	/* Reset missing clock */
-#define	DISDPLL	0x60	/* Disable DPLL */
-#define	SSBR	0x80	/* Set DPLL source = BR generator */
-#define	SSRTxC	0xa0	/* Set DPLL source = RTxC */
-#define	SFMM	0xc0	/* Set FM mode */
-#define	SNRZI	0xe0	/* Set NRZI mode */
-
-/* Write Register 15 (external/status interrupt control) */
-#define	ZCIE	2	/* Zero count IE */
-#define	DCDIE	8	/* DCD IE */
-#define	SYNCIE	0x10	/* Sync/hunt IE */
-#define	CTSIE	0x20	/* CTS IE */
-#define	TxUIE	0x40	/* Tx Underrun/EOM IE */
-#define	BRKIE	0x80	/* Break/Abort IE */
-
-
-/* Read Register 0 */
-#define	Rx_CH_AV	0x1	/* Rx Character Available */
-#define	ZCOUNT		0x2	/* Zero count */
-#define	Tx_BUF_EMP	0x4	/* Tx Buffer empty */
-#define	DCD		0x8	/* DCD */
-#define	SYNC		0x10	/* Sync/hunt */
-#define	CTS		0x20	/* CTS */
-#define	TxEOM		0x40	/* Tx underrun */
-#define	BRK_ABRT	0x80	/* Break/Abort */
-
-/* Read Register 1 */
-#define	ALL_SNT		0x1	/* All sent */
-/* Residue Data for 8 Rx bits/char programmed */
-#define	RES3		0x8	/* 0/3 */
-#define	RES4		0x4	/* 0/4 */
-#define	RES5		0xc	/* 0/5 */
-#define	RES6		0x2	/* 0/6 */
-#define	RES7		0xa	/* 0/7 */
-#define	RES8		0x6	/* 0/8 */
-#define	RES18		0xe	/* 1/8 */
-#define	RES28		0x0	/* 2/8 */
-/* Special Rx Condition Interrupts */
-#define	PAR_ERR		0x10	/* Parity error */
-#define	Rx_OVR		0x20	/* Rx Overrun Error */
-#define	CRC_ERR		0x40	/* CRC/Framing Error */
-#define	END_FR		0x80	/* End of Frame (SDLC) */
-
-/* Read Register 2 (channel b only) - Interrupt vector */
-
-/* Read Register 3 (interrupt pending register) ch a only */
-#define	CHBEXT	0x1		/* Channel B Ext/Stat IP */
-#define	CHBTxIP	0x2		/* Channel B Tx IP */
-#define	CHBRxIP	0x4		/* Channel B Rx IP */
-#define	CHAEXT	0x8		/* Channel A Ext/Stat IP */
-#define	CHATxIP	0x10		/* Channel A Tx IP */
-#define	CHARxIP	0x20		/* Channel A Rx IP */
-
-/* Read Register 8 (receive data register) */
-
-/* Read Register 10  (misc status bits) */
-#define	ONLOOP	2		/* On loop */
-#define	LOOPSEND 0x10		/* Loop sending */
-#define	CLK2MIS	0x40		/* Two clocks missing */
-#define	CLK1MIS	0x80		/* One clock missing */
-
-/* Read Register 12 (lower byte of baud rate generator constant) */
-
-/* Read Register 13 (upper byte of baud rate generator constant) */
-
-/* Read Register 15 (value of WR 15) */
-
-/* Misc inlines */
-static inline void ZS_CLEARERR(struct sgi_zschannel *channel)
-{
-	volatile unsigned char junk;
-
-	udelay(2);
-	channel->control = ERR_RES;
-	if (ioc_icontrol)
-		junk = ioc_icontrol->istat0;
-}
-
-static inline void ZS_CLEARFIFO(struct sgi_zschannel *channel)
-{
-	volatile unsigned char junk;
-
-	udelay(2);
-	junk = channel->data;
-	udelay(2);
-	if (ioc_icontrol)
-		junk = ioc_icontrol->istat0;
-	junk = channel->data;
-	udelay(2);
-	if (ioc_icontrol)
-		junk = ioc_icontrol->istat0;
-	junk = channel->data;
-	udelay(2);
-	if (ioc_icontrol)
-		junk = ioc_icontrol->istat0;
-}
-
-#if 0
-
-#define ZS_CLEARERR(channel)    (channel->control = ERR_RES)
-#define ZS_CLEARFIFO(channel)   do { volatile unsigned char garbage; \
-				     garbage = channel->data; \
-				     udelay(2); \
-				     garbage = channel->data; \
-				     udelay(2); \
-				     garbage = channel->data; \
-				     udelay(2); } while(0)
-
-#endif
-
-#endif /* !(_SPARC_SERIAL_H) */

FUNET's LINUX-ADM group, linux-adm@nic.funet.fi
TCL-scripts by Sam Shen (who was at: slshen@lbl.gov)