patch-2.4.23 linux-2.4.23/drivers/usb/gadget/net2280.h
Next file: linux-2.4.23/drivers/usb/gadget/usbstring.c
Previous file: linux-2.4.23/drivers/usb/gadget/net2280.c
Back to the patch index
Back to the overall index
- Lines: 756
- Date:
2003-11-28 10:26:20.000000000 -0800
- Orig file:
linux-2.4.22/drivers/usb/gadget/net2280.h
- Orig date:
1969-12-31 16:00:00.000000000 -0800
diff -urN linux-2.4.22/drivers/usb/gadget/net2280.h linux-2.4.23/drivers/usb/gadget/net2280.h
@@ -0,0 +1,755 @@
+/*
+ * NetChip 2280 high/full speed USB device controller.
+ * Unlike many such controllers, this one talks PCI.
+ */
+
+/*
+ * Copyright (C) 2002 NetChip Technology, Inc. (http://www.netchip.com)
+ * Copyright (C) 2003 David Brownell
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+/*-------------------------------------------------------------------------*/
+
+/* NET2280 MEMORY MAPPED REGISTERS
+ *
+ * The register layout came from the chip documentation, and the bit
+ * number definitions were extracted from chip specification.
+ *
+ * Use the shift operator ('<<') to build bit masks, with readl/writel
+ * to access the registers through PCI.
+ */
+
+/* main registers, BAR0 + 0x0000 */
+struct net2280_regs {
+ // offset 0x0000
+ u32 devinit;
+#define LOCAL_CLOCK_FREQUENCY 8
+#define FORCE_PCI_RESET 7
+#define PCI_ID 6
+#define PCI_ENABLE 5
+#define FIFO_SOFT_RESET 4
+#define CFG_SOFT_RESET 3
+#define PCI_SOFT_RESET 2
+#define USB_SOFT_RESET 1
+#define M8051_RESET 0
+ u32 eectl;
+#define EEPROM_ADDRESS_WIDTH 23
+#define EEPROM_CHIP_SELECT_ACTIVE 22
+#define EEPROM_PRESENT 21
+#define EEPROM_VALID 20
+#define EEPROM_BUSY 19
+#define EEPROM_CHIP_SELECT_ENABLE 18
+#define EEPROM_BYTE_READ_START 17
+#define EEPROM_BYTE_WRITE_START 16
+#define EEPROM_READ_DATA 8
+#define EEPROM_WRITE_DATA 0
+ u32 eeclkfreq;
+ u32 _unused0;
+ // offset 0x0010
+
+ u32 pciirqenb0; /* interrupt PCI master ... */
+#define SETUP_PACKET_INTERRUPT_ENABLE 7
+#define ENDPOINT_F_INTERRUPT_ENABLE 6
+#define ENDPOINT_E_INTERRUPT_ENABLE 5
+#define ENDPOINT_D_INTERRUPT_ENABLE 4
+#define ENDPOINT_C_INTERRUPT_ENABLE 3
+#define ENDPOINT_B_INTERRUPT_ENABLE 2
+#define ENDPOINT_A_INTERRUPT_ENABLE 1
+#define ENDPOINT_0_INTERRUPT_ENABLE 0
+ u32 pciirqenb1;
+#define PCI_INTERRUPT_ENABLE 31
+#define POWER_STATE_CHANGE_INTERRUPT_ENABLE 27
+#define PCI_ARBITER_TIMEOUT_INTERRUPT_ENABLE 26
+#define PCI_PARITY_ERROR_INTERRUPT_ENABLE 25
+#define PCI_MASTER_ABORT_RECEIVED_INTERRUPT_ENABLE 20
+#define PCI_TARGET_ABORT_RECEIVED_INTERRUPT_ENABLE 19
+#define PCI_TARGET_ABORT_ASSERTED_INTERRUPT_ENABLE 18
+#define PCI_RETRY_ABORT_INTERRUPT_ENABLE 17
+#define PCI_MASTER_CYCLE_DONE_INTERRUPT_ENABLE 16
+#define GPIO_INTERRUPT_ENABLE 13
+#define DMA_D_INTERRUPT_ENABLE 12
+#define DMA_C_INTERRUPT_ENABLE 11
+#define DMA_B_INTERRUPT_ENABLE 10
+#define DMA_A_INTERRUPT_ENABLE 9
+#define EEPROM_DONE_INTERRUPT_ENABLE 8
+#define VBUS_INTERRUPT_ENABLE 7
+#define CONTROL_STATUS_INTERRUPT_ENABLE 6
+#define ROOT_PORT_RESET_INTERRUPT_ENABLE 4
+#define SUSPEND_REQUEST_INTERRUPT_ENABLE 3
+#define SUSPEND_REQUEST_CHANGE_INTERRUPT_ENABLE 2
+#define RESUME_INTERRUPT_ENABLE 1
+#define SOF_INTERRUPT_ENABLE 0
+ u32 cpu_irqenb0; /* ... or onboard 8051 */
+#define SETUP_PACKET_INTERRUPT_ENABLE 7
+#define ENDPOINT_F_INTERRUPT_ENABLE 6
+#define ENDPOINT_E_INTERRUPT_ENABLE 5
+#define ENDPOINT_D_INTERRUPT_ENABLE 4
+#define ENDPOINT_C_INTERRUPT_ENABLE 3
+#define ENDPOINT_B_INTERRUPT_ENABLE 2
+#define ENDPOINT_A_INTERRUPT_ENABLE 1
+#define ENDPOINT_0_INTERRUPT_ENABLE 0
+ u32 cpu_irqenb1;
+#define CPU_INTERRUPT_ENABLE 31
+#define POWER_STATE_CHANGE_INTERRUPT_ENABLE 27
+#define PCI_ARBITER_TIMEOUT_INTERRUPT_ENABLE 26
+#define PCI_PARITY_ERROR_INTERRUPT_ENABLE 25
+#define PCI_INTA_INTERRUPT_ENABLE 24
+#define PCI_PME_INTERRUPT_ENABLE 23
+#define PCI_SERR_INTERRUPT_ENABLE 22
+#define PCI_PERR_INTERRUPT_ENABLE 21
+#define PCI_MASTER_ABORT_RECEIVED_INTERRUPT_ENABLE 20
+#define PCI_TARGET_ABORT_RECEIVED_INTERRUPT_ENABLE 19
+#define PCI_RETRY_ABORT_INTERRUPT_ENABLE 17
+#define PCI_MASTER_CYCLE_DONE_INTERRUPT_ENABLE 16
+#define GPIO_INTERRUPT_ENABLE 13
+#define DMA_D_INTERRUPT_ENABLE 12
+#define DMA_C_INTERRUPT_ENABLE 11
+#define DMA_B_INTERRUPT_ENABLE 10
+#define DMA_A_INTERRUPT_ENABLE 9
+#define EEPROM_DONE_INTERRUPT_ENABLE 8
+#define VBUS_INTERRUPT_ENABLE 7
+#define CONTROL_STATUS_INTERRUPT_ENABLE 6
+#define ROOT_PORT_RESET_INTERRUPT_ENABLE 4
+#define SUSPEND_REQUEST_INTERRUPT_ENABLE 3
+#define SUSPEND_REQUEST_CHANGE_INTERRUPT_ENABLE 2
+#define RESUME_INTERRUPT_ENABLE 1
+#define SOF_INTERRUPT_ENABLE 0
+
+ // offset 0x0020
+ u32 _unused1;
+ u32 usbirqenb1;
+#define USB_INTERRUPT_ENABLE 31
+#define POWER_STATE_CHANGE_INTERRUPT_ENABLE 27
+#define PCI_ARBITER_TIMEOUT_INTERRUPT_ENABLE 26
+#define PCI_PARITY_ERROR_INTERRUPT_ENABLE 25
+#define PCI_INTA_INTERRUPT_ENABLE 24
+#define PCI_PME_INTERRUPT_ENABLE 23
+#define PCI_SERR_INTERRUPT_ENABLE 22
+#define PCI_PERR_INTERRUPT_ENABLE 21
+#define PCI_MASTER_ABORT_RECEIVED_INTERRUPT_ENABLE 20
+#define PCI_TARGET_ABORT_RECEIVED_INTERRUPT_ENABLE 19
+#define PCI_RETRY_ABORT_INTERRUPT_ENABLE 17
+#define PCI_MASTER_CYCLE_DONE_INTERRUPT_ENABLE 16
+#define GPIO_INTERRUPT_ENABLE 13
+#define DMA_D_INTERRUPT_ENABLE 12
+#define DMA_C_INTERRUPT_ENABLE 11
+#define DMA_B_INTERRUPT_ENABLE 10
+#define DMA_A_INTERRUPT_ENABLE 9
+#define EEPROM_DONE_INTERRUPT_ENABLE 8
+#define VBUS_INTERRUPT_ENABLE 7
+#define CONTROL_STATUS_INTERRUPT_ENABLE 6
+#define ROOT_PORT_RESET_INTERRUPT_ENABLE 4
+#define SUSPEND_REQUEST_INTERRUPT_ENABLE 3
+#define SUSPEND_REQUEST_CHANGE_INTERRUPT_ENABLE 2
+#define RESUME_INTERRUPT_ENABLE 1
+#define SOF_INTERRUPT_ENABLE 0
+ u32 irqstat0;
+#define INTA_ASSERTED 12
+#define SETUP_PACKET_INTERRUPT 7
+#define ENDPOINT_F_INTERRUPT 6
+#define ENDPOINT_E_INTERRUPT 5
+#define ENDPOINT_D_INTERRUPT 4
+#define ENDPOINT_C_INTERRUPT 3
+#define ENDPOINT_B_INTERRUPT 2
+#define ENDPOINT_A_INTERRUPT 1
+#define ENDPOINT_0_INTERRUPT 0
+ u32 irqstat1;
+#define POWER_STATE_CHANGE_INTERRUPT 27
+#define PCI_ARBITER_TIMEOUT_INTERRUPT 26
+#define PCI_PARITY_ERROR_INTERRUPT 25
+#define PCI_INTA_INTERRUPT 24
+#define PCI_PME_INTERRUPT 23
+#define PCI_SERR_INTERRUPT 22
+#define PCI_PERR_INTERRUPT 21
+#define PCI_MASTER_ABORT_RECEIVED_INTERRUPT 20
+#define PCI_TARGET_ABORT_RECEIVED_INTERRUPT 19
+#define PCI_RETRY_ABORT_INTERRUPT 17
+#define PCI_MASTER_CYCLE_DONE_INTERRUPT 16
+#define GPIO_INTERRUPT 13
+#define DMA_D_INTERRUPT 12
+#define DMA_C_INTERRUPT 11
+#define DMA_B_INTERRUPT 10
+#define DMA_A_INTERRUPT 9
+#define EEPROM_DONE_INTERRUPT 8
+#define VBUS_INTERRUPT 7
+#define CONTROL_STATUS_INTERRUPT 6
+#define ROOT_PORT_RESET_INTERRUPT 4
+#define SUSPEND_REQUEST_INTERRUPT 3
+#define SUSPEND_REQUEST_CHANGE_INTERRUPT 2
+#define RESUME_INTERRUPT 1
+#define SOF_INTERRUPT 0
+ // offset 0x0030
+ u32 idxaddr;
+ u32 idxdata;
+ u32 fifoctl;
+#define PCI_BASE2_RANGE 16
+#define IGNORE_FIFO_AVAILABILITY 3
+#define PCI_BASE2_SELECT 2
+#define FIFO_CONFIGURATION_SELECT 0
+ u32 _unused2;
+ // offset 0x0040
+ u32 memaddr;
+#define START 28
+#define DIRECTION 27
+#define FIFO_DIAGNOSTIC_SELECT 24
+#define MEMORY_ADDRESS 0
+ u32 memdata0;
+ u32 memdata1;
+ u32 _unused3;
+ // offset 0x0050
+ u32 gpioctl;
+#define GPIO3_LED_SELECT 12
+#define GPIO3_INTERRUPT_ENABLE 11
+#define GPIO2_INTERRUPT_ENABLE 10
+#define GPIO1_INTERRUPT_ENABLE 9
+#define GPIO0_INTERRUPT_ENABLE 8
+#define GPIO3_OUTPUT_ENABLE 7
+#define GPIO2_OUTPUT_ENABLE 6
+#define GPIO1_OUTPUT_ENABLE 5
+#define GPIO0_OUTPUT_ENABLE 4
+#define GPIO3_DATA 3
+#define GPIO2_DATA 2
+#define GPIO1_DATA 1
+#define GPIO0_DATA 0
+ u32 gpiostat;
+#define GPIO3_INTERRUPT 3
+#define GPIO2_INTERRUPT 2
+#define GPIO1_INTERRUPT 1
+#define GPIO0_INTERRUPT 0
+} __attribute__ ((packed));
+
+/* usb control, BAR0 + 0x0080 */
+struct net2280_usb_regs {
+ // offset 0x0080
+ u32 stdrsp;
+#define STALL_UNSUPPORTED_REQUESTS 31
+#define SET_TEST_MODE 16
+#define GET_OTHER_SPEED_CONFIGURATION 15
+#define GET_DEVICE_QUALIFIER 14
+#define SET_ADDRESS 13
+#define ENDPOINT_SET_CLEAR_HALT 12
+#define DEVICE_SET_CLEAR_DEVICE_REMOTE_WAKEUP 11
+#define GET_STRING_DESCRIPTOR_2 10
+#define GET_STRING_DESCRIPTOR_1 9
+#define GET_STRING_DESCRIPTOR_0 8
+#define GET_SET_INTERFACE 6
+#define GET_SET_CONFIGURATION 5
+#define GET_CONFIGURATION_DESCRIPTOR 4
+#define GET_DEVICE_DESCRIPTOR 3
+#define GET_ENDPOINT_STATUS 2
+#define GET_INTERFACE_STATUS 1
+#define GET_DEVICE_STATUS 0
+ u32 prodvendid;
+#define PRODUCT_ID 16
+#define VENDOR_ID 0
+ u32 relnum;
+ u32 usbctl;
+#define SERIAL_NUMBER_INDEX 16
+#define PRODUCT_ID_STRING_ENABLE 13
+#define VENDOR_ID_STRING_ENABLE 12
+#define USB_ROOT_PORT_WAKEUP_ENABLE 11
+#define VBUS_PIN 10
+#define TIMED_DISCONNECT 9
+#define SUSPEND_IMMEDIATELY 7
+#define SELF_POWERED_USB_DEVICE 6
+#define REMOTE_WAKEUP_SUPPORT 5
+#define PME_POLARITY 4
+#define USB_DETECT_ENABLE 3
+#define PME_WAKEUP_ENABLE 2
+#define DEVICE_REMOTE_WAKEUP_ENABLE 1
+#define SELF_POWERED_STATUS 0
+ // offset 0x0090
+ u32 usbstat;
+#define HIGH_SPEED 7
+#define FULL_SPEED 6
+#define GENERATE_RESUME 5
+#define GENERATE_DEVICE_REMOTE_WAKEUP 4
+ u32 xcvrdiag;
+#define FORCE_HIGH_SPEED_MODE 31
+#define FORCE_FULL_SPEED_MODE 30
+#define USB_TEST_MODE 24
+#define LINE_STATE 16
+#define TRANSCEIVER_OPERATION_MODE 2
+#define TRANSCEIVER_SELECT 1
+#define TERMINATION_SELECT 0
+ u32 setup0123;
+ u32 setup4567;
+ // offset 0x0090
+ u32 _unused0;
+ u32 ouraddr;
+#define FORCE_IMMEDIATE 7
+#define OUR_USB_ADDRESS 0
+ u32 ourconfig;
+} __attribute__ ((packed));
+
+/* pci control, BAR0 + 0x0100 */
+struct net2280_pci_regs {
+ // offset 0x0100
+ u32 pcimstctl;
+#define PCI_ARBITER_PARK_SELECT 13
+#define PCI_MULTI LEVEL_ARBITER 12
+#define PCI_RETRY_ABORT_ENABLE 11
+#define DMA_MEMORY_WRITE_AND_INVALIDATE_ENABLE 10
+#define DMA_READ_MULTIPLE_ENABLE 9
+#define DMA_READ_LINE_ENABLE 8
+#define PCI_MASTER_COMMAND_SELECT 6
+#define MEM_READ_OR_WRITE 0
+#define IO_READ_OR_WRITE 1
+#define CFG_READ_OR_WRITE 2
+#define PCI_MASTER_START 5
+#define PCI_MASTER_READ_WRITE 4
+#define PCI_MASTER_WRITE 0
+#define PCI_MASTER_READ 1
+#define PCI_MASTER_BYTE_WRITE_ENABLES 0
+ u32 pcimstaddr;
+ u32 pcimstdata;
+ u32 pcimststat;
+#define PCI_ARBITER_CLEAR 2
+#define PCI_EXTERNAL_ARBITER 1
+#define PCI_HOST_MODE 0
+} __attribute__ ((packed));
+
+/* dma control, BAR0 + 0x0180 ... array of four structs like this,
+ * for channels 0..3. see also struct net2280_dma: descriptor
+ * that can be loaded into some of these registers.
+ */
+struct net2280_dma_regs { /* [11.7] */
+ // offset 0x0180, 0x01a0, 0x01c0, 0x01e0,
+ u32 dmactl;
+#define DMA_SCATTER_GATHER_DONE_INTERRUPT_ENABLE 25
+#define DMA_CLEAR_COUNT_ENABLE 21
+#define DESCRIPTOR_POLLING_RATE 19
+#define POLL_CONTINUOUS 0
+#define POLL_1_USEC 1
+#define POLL_100_USEC 2
+#define POLL_1_MSEC 3
+#define DMA_VALID_BIT_POLLING_ENABLE 18
+#define DMA_VALID_BIT_ENABLE 17
+#define DMA_SCATTER_GATHER_ENABLE 16
+#define DMA_OUT_AUTO_START_ENABLE 4
+#define DMA_PREEMPT_ENABLE 3
+#define DMA_FIFO_VALIDATE 2
+#define DMA_ENABLE 1
+#define DMA_ADDRESS_HOLD 0
+ u32 dmastat;
+#define DMA_SCATTER_GATHER_DONE_INTERRUPT 25
+#define DMA_TRANSACTION_DONE_INTERRUPT 24
+#define DMA_ABORT 1
+#define DMA_START 0
+ u32 _unused0 [2];
+ // offset 0x0190, 0x01b0, 0x01d0, 0x01f0,
+ u32 dmacount;
+#define VALID_BIT 31
+#define DMA_DIRECTION 30
+#define DMA_DONE_INTERRUPT_ENABLE 29
+#define END_OF_CHAIN 28
+#define DMA_BYTE_COUNT_MASK ((1<<24)-1)
+#define DMA_BYTE_COUNT 0
+ u32 dmaaddr;
+ u32 dmadesc;
+ u32 _unused1;
+} __attribute__ ((packed));
+
+/* dedicated endpoint registers, BAR0 + 0x0200 */
+
+struct net2280_dep_regs { /* [11.8] */
+ // offset 0x0200, 0x0210, 0x220, 0x230, 0x240
+ u32 dep_cfg;
+ // offset 0x0204, 0x0214, 0x224, 0x234, 0x244
+ u32 dep_rsp;
+ u32 _unused [2];
+} __attribute__ ((packed));
+
+/* configurable endpoint registers, BAR0 + 0x0300 ... array of seven structs
+ * like this, for ep0 then the configurable endpoints A..F
+ * ep0 reserved for control; E and F have only 64 bytes of fifo
+ */
+struct net2280_ep_regs { /* [11.9] */
+ // offset 0x0300, 0x0320, 0x0340, 0x0360, 0x0380, 0x03a0, 0x03c0
+ u32 ep_cfg;
+#define ENDPOINT_BYTE_COUNT 16
+#define ENDPOINT_ENABLE 10
+#define ENDPOINT_TYPE 8
+#define ENDPOINT_DIRECTION 7
+#define ENDPOINT_NUMBER 0
+ u32 ep_rsp;
+#define SET_NAK_OUT_PACKETS 15
+#define SET_EP_HIDE_STATUS_PHASE 14
+#define SET_EP_FORCE_CRC_ERROR 13
+#define SET_INTERRUPT_MODE 12
+#define SET_CONTROL_STATUS_PHASE_HANDSHAKE 11
+#define SET_NAK_OUT_PACKETS_MODE 10
+#define SET_ENDPOINT_TOGGLE 9
+#define SET_ENDPOINT_HALT 8
+#define CLEAR_NAK_OUT_PACKETS 7
+#define CLEAR_EP_HIDE_STATUS_PHASE 6
+#define CLEAR_EP_FORCE_CRC_ERROR 5
+#define CLEAR_INTERRUPT_MODE 4
+#define CLEAR_CONTROL_STATUS_PHASE_HANDSHAKE 3
+#define CLEAR_NAK_OUT_PACKETS_MODE 2
+#define CLEAR_ENDPOINT_TOGGLE 1
+#define CLEAR_ENDPOINT_HALT 0
+ u32 ep_irqenb;
+#define SHORT_PACKET_OUT_DONE_INTERRUPT_ENABLE 6
+#define SHORT_PACKET_TRANSFERRED_INTERRUPT_ENABLE 5
+#define DATA_PACKET_RECEIVED_INTERRUPT_ENABLE 3
+#define DATA_PACKET_TRANSMITTED_INTERRUPT_ENABLE 2
+#define DATA_OUT_PING_TOKEN_INTERRUPT_ENABLE 1
+#define DATA_IN_TOKEN_INTERRUPT_ENABLE 0
+ u32 ep_stat;
+#define FIFO_VALID_COUNT 24
+#define HIGH_BANDWIDTH_OUT_TRANSACTION_PID 22
+#define TIMEOUT 21
+#define USB_STALL_SENT 20
+#define USB_IN_NAK_SENT 19
+#define USB_IN_ACK_RCVD 18
+#define USB_OUT_PING_NAK_SENT 17
+#define USB_OUT_ACK_SENT 16
+#define FIFO_OVERFLOW 13
+#define FIFO_UNDERFLOW 12
+#define FIFO_FULL 11
+#define FIFO_EMPTY 10
+#define FIFO_FLUSH 9
+#define SHORT_PACKET_OUT_DONE_INTERRUPT 6
+#define SHORT_PACKET_TRANSFERRED_INTERRUPT 5
+#define NAK_OUT_PACKETS 4
+#define DATA_PACKET_RECEIVED_INTERRUPT 3
+#define DATA_PACKET_TRANSMITTED_INTERRUPT 2
+#define DATA_OUT_PING_TOKEN_INTERRUPT 1
+#define DATA_IN_TOKEN_INTERRUPT 0
+ // offset 0x0310, 0x0330, 0x0350, 0x0370, 0x0390, 0x03b0, 0x03d0
+ u32 ep_avail;
+ u32 ep_data;
+ u32 _unused0 [2];
+} __attribute__ ((packed));
+
+/*-------------------------------------------------------------------------*/
+
+#ifdef __KERNEL__
+
+/* indexed registers [11.10] are accessed indirectly
+ * caller must own the device lock.
+ */
+
+static inline u32
+get_idx_reg (struct net2280_regs *regs, u32 index)
+{
+ writel (index, ®s->idxaddr);
+ /* NOTE: synchs device/cpu memory views */
+ return readl (®s->idxdata);
+}
+
+static inline void
+set_idx_reg (struct net2280_regs *regs, u32 index, u32 value)
+{
+ writel (index, ®s->idxaddr);
+ writel (value, ®s->idxdata);
+ /* posted, may not be visible yet */
+}
+
+#endif /* __KERNEL__ */
+
+
+#define REG_DIAG 0x0
+#define RETRY_COUNTER 16
+#define FORCE_PCI_SERR 11
+#define FORCE_PCI_INTERRUPT 10
+#define FORCE_USB_INTERRUPT 9
+#define FORCE_CPU_INTERRUPT 8
+#define ILLEGAL_BYTE_ENABLES 5
+#define FAST_TIMES 4
+#define FORCE_RECEIVE_ERROR 2
+#define FORCE_TRANSMIT_CRC_ERROR 0
+#define REG_FRAME 0x02 /* from last sof */
+#define REG_CHIPREV 0x03 /* in bcd */
+#define REG_HS_NAK_RATE 0x0a /* NAK per N uframes */
+
+#define CHIPREV_1 0x0100
+#define CHIPREV_1A 0x0110
+
+#ifdef __KERNEL__
+
+/* ep a-f highspeed and fullspeed maxpacket, addresses
+ * computed from ep->num
+ */
+#define REG_EP_MAXPKT(dev,num) (((num) + 1) * 0x10 + \
+ (((dev)->gadget.speed == USB_SPEED_HIGH) ? 0 : 1))
+
+/*-------------------------------------------------------------------------*/
+
+/* [8.3] for scatter/gather i/o
+ * use struct net2280_dma_regs bitfields
+ */
+struct net2280_dma {
+ u32 dmacount;
+ u32 dmaaddr; /* the buffer */
+ u32 dmadesc; /* next dma descriptor */
+ u32 _reserved;
+} __attribute__ ((aligned (16)));
+
+/*-------------------------------------------------------------------------*/
+
+/* DRIVER DATA STRUCTURES and UTILITIES */
+
+struct net2280_ep {
+ struct usb_ep ep;
+ struct net2280_ep_regs *regs;
+ struct net2280_dma_regs *dma;
+ struct net2280_dma *dummy;
+ dma_addr_t td_dma; /* of dummy */
+ struct net2280 *dev;
+ unsigned long irqs;
+
+ /* analogous to a host-side qh */
+ struct list_head queue;
+ const struct usb_endpoint_descriptor *desc;
+ unsigned num : 8,
+ fifo_size : 12,
+ in_fifo_validate : 1,
+ stopped : 1,
+ is_in : 1,
+ is_iso : 1;
+};
+
+static inline void allow_status (struct net2280_ep *ep)
+{
+ /* ep0 only */
+ writel ( (1 << CLEAR_CONTROL_STATUS_PHASE_HANDSHAKE)
+ | (1 << CLEAR_NAK_OUT_PACKETS_MODE)
+ , &ep->regs->ep_rsp);
+ ep->stopped = 1;
+}
+
+/* count (<= 4) bytes in the next fifo write will be valid */
+static inline void set_fifo_bytecount (struct net2280_ep *ep, unsigned count)
+{
+ writeb (count, 2 + (u8 *) &ep->regs->ep_cfg);
+}
+
+struct net2280_request {
+ struct usb_request req;
+ struct net2280_dma *td;
+ dma_addr_t td_dma;
+ struct list_head queue;
+ unsigned mapped : 1,
+ dma_done : 1,
+ valid : 1;
+};
+
+struct net2280 {
+ /* each pci device provides one gadget, several endpoints */
+ struct usb_gadget gadget;
+ spinlock_t lock;
+ struct net2280_ep ep [7];
+ struct usb_gadget_driver *driver;
+ unsigned enabled : 1,
+ protocol_stall : 1,
+ got_irq : 1,
+ region : 1,
+ selfpowered : 1;
+ u16 chiprev;
+
+ /* pci state used to access those endpoints */
+ struct pci_dev *pdev;
+ struct net2280_regs *regs;
+ struct net2280_usb_regs *usb;
+ struct net2280_pci_regs *pci;
+ struct net2280_dma_regs *dma;
+ struct net2280_dep_regs *dep;
+ struct net2280_ep_regs *epregs;
+
+ struct pci_pool *requests;
+ // statistics...
+};
+
+static inline void set_halt (struct net2280_ep *ep)
+{
+ /* ep0 and bulk/intr endpoints */
+ writel ( (1 << CLEAR_CONTROL_STATUS_PHASE_HANDSHAKE)
+ /* set NAK_OUT for erratum 0114 */
+ | ((ep->dev->chiprev == CHIPREV_1) << SET_NAK_OUT_PACKETS)
+ | (1 << SET_ENDPOINT_HALT)
+ , &ep->regs->ep_rsp);
+}
+
+static inline void clear_halt (struct net2280_ep *ep)
+{
+ /* ep0 and bulk/intr endpoints */
+ writel ( (1 << CLEAR_ENDPOINT_HALT)
+ | (1 << CLEAR_ENDPOINT_TOGGLE)
+ /* unless the gadget driver left a short packet in the
+ * fifo, this reverses the erratum 0114 workaround.
+ */
+ | ((ep->dev->chiprev == CHIPREV_1) << CLEAR_NAK_OUT_PACKETS)
+ , &ep->regs->ep_rsp);
+}
+
+#ifdef USE_RDK_LEDS
+
+static inline void net2280_led_init (struct net2280 *dev)
+{
+ /* LED3 (green) is on during USB activity. note erratum 0113. */
+ writel ((1 << GPIO3_LED_SELECT)
+ | (1 << GPIO3_OUTPUT_ENABLE)
+ | (1 << GPIO2_OUTPUT_ENABLE)
+ | (1 << GPIO1_OUTPUT_ENABLE)
+ | (1 << GPIO0_OUTPUT_ENABLE)
+ , &dev->regs->gpioctl);
+}
+
+/* indicate speed with bi-color LED 0/1 */
+static inline
+void net2280_led_speed (struct net2280 *dev, enum usb_device_speed speed)
+{
+ u32 val = readl (&dev->regs->gpioctl);
+ switch (speed) {
+ case USB_SPEED_HIGH: /* green */
+ val &= ~(1 << GPIO0_DATA);
+ val |= (1 << GPIO1_DATA);
+ break;
+ case USB_SPEED_FULL: /* red */
+ val &= ~(1 << GPIO1_DATA);
+ val |= (1 << GPIO0_DATA);
+ break;
+ default: /* (off/black) */
+ val &= ~((1 << GPIO1_DATA) | (1 << GPIO0_DATA));
+ break;
+ }
+ writel (val, &dev->regs->gpioctl);
+}
+
+/* indicate power with LED 2 */
+static inline void net2280_led_active (struct net2280 *dev, int is_active)
+{
+ u32 val = readl (&dev->regs->gpioctl);
+
+ // FIXME this LED never seems to turn on.
+ if (is_active)
+ val |= GPIO2_DATA;
+ else
+ val &= ~GPIO2_DATA;
+ writel (val, &dev->regs->gpioctl);
+}
+static inline void net2280_led_shutdown (struct net2280 *dev)
+{
+ /* turn off all four GPIO*_DATA bits */
+ writel (readl (&dev->regs->gpioctl) & ~0x0f,
+ &dev->regs->gpioctl);
+}
+
+#else
+
+#define net2280_led_init(dev) do { } while (0)
+#define net2280_led_speed(dev, speed) do { } while (0)
+#define net2280_led_shutdown(dev) do { } while (0)
+
+#endif
+
+/*-------------------------------------------------------------------------*/
+
+#define xprintk(dev,level,fmt,args...) \
+ printk(level "%s %s: " fmt , driver_name , \
+ dev->pdev->slot_name , ## args)
+
+#ifdef DEBUG
+#undef DEBUG
+#define DEBUG(dev,fmt,args...) \
+ xprintk(dev , KERN_DEBUG , fmt , ## args)
+#else
+#define DEBUG(dev,fmt,args...) \
+ do { } while (0)
+#endif /* DEBUG */
+
+#ifdef VERBOSE
+#define VDEBUG DEBUG
+#else
+#define VDEBUG(dev,fmt,args...) \
+ do { } while (0)
+#endif /* VERBOSE */
+
+#define ERROR(dev,fmt,args...) \
+ xprintk(dev , KERN_ERR , fmt , ## args)
+#define WARN(dev,fmt,args...) \
+ xprintk(dev , KERN_WARNING , fmt , ## args)
+#define INFO(dev,fmt,args...) \
+ xprintk(dev , KERN_INFO , fmt , ## args)
+
+/*-------------------------------------------------------------------------*/
+
+static inline void start_out_naking (struct net2280_ep *ep)
+{
+ /* NOTE: hardware races lurk here, and PING protocol issues */
+ writel ((1 << SET_NAK_OUT_PACKETS), &ep->regs->ep_rsp);
+ /* synch with device */
+ readl (&ep->regs->ep_rsp);
+}
+
+#ifdef DEBUG
+static inline void assert_out_naking (struct net2280_ep *ep, const char *where)
+{
+ u32 tmp = readl (&ep->regs->ep_stat);
+
+ if ((tmp & (1 << NAK_OUT_PACKETS)) == 0) {
+ DEBUG (ep->dev, "%s %s %08x !NAK\n",
+ ep->ep.name, where, tmp);
+ writel ((1 << SET_NAK_OUT_PACKETS),
+ &ep->regs->ep_rsp);
+ }
+}
+#define ASSERT_OUT_NAKING(ep) assert_out_naking(ep,__FUNCTION__)
+#else
+#define ASSERT_OUT_NAKING(ep) do {} while (0)
+#endif
+
+static inline void stop_out_naking (struct net2280_ep *ep)
+{
+ u32 tmp;
+
+ tmp = readl (&ep->regs->ep_stat);
+ if ((tmp & (1 << NAK_OUT_PACKETS)) != 0)
+ writel ((1 << CLEAR_NAK_OUT_PACKETS), &ep->regs->ep_rsp);
+}
+
+/*-------------------------------------------------------------------------*/
+
+/* 2.5 and 2.4.older portability changes ... */
+
+#ifndef container_of
+#define container_of list_entry
+#endif
+
+#ifndef likely
+#define likely(x) (x)
+#define unlikely(x) (x)
+#endif
+
+#ifndef BUG_ON
+#define BUG_ON(condition) do { if (unlikely((condition)!=0)) BUG(); } while(0)
+#endif
+
+#ifndef WARN_ON
+#define WARN_ON(x) do { } while (0)
+#endif
+
+#ifndef IRQ_NONE
+typedef void irqreturn_t;
+#define IRQ_NONE
+#define IRQ_HANDLED
+#define IRQ_RETVAL(x)
+#endif
+
+#endif /* __KERNEL__ */
FUNET's LINUX-ADM group, linux-adm@nic.funet.fi
TCL-scripts by Sam Shen (who was at: slshen@lbl.gov)