patch-2.4.5 linux/drivers/net/wireless/orinoco.c
Next file: linux/drivers/net/wireless/orinoco.h
Previous file: linux/drivers/net/wireless/hermes.h
Back to the patch index
Back to the overall index
- Lines: 3552
- Date:
Mon May 7 19:42:14 2001
- Orig file:
v2.4.4/linux/drivers/net/wireless/orinoco.c
- Orig date:
Wed Dec 31 16:00:00 1969
diff -u --recursive --new-file v2.4.4/linux/drivers/net/wireless/orinoco.c linux/drivers/net/wireless/orinoco.c
@@ -0,0 +1,3551 @@
+/* orinoco.c 0.05 - (formerly known as dldwd_cs.c and orinoco_cs.c)
+ *
+ * A driver for "Hermes" chipset based PCMCIA wireless adaptors, such
+ * as the Lucent WavelanIEEE/Orinoco cards and their OEM (Cabletron/
+ * EnteraSys RoamAbout 802.11, ELSA Airlancer, Melco Buffalo and others).
+ * It should also be usable on various Prism II based cards such as the
+ * Linksys, D-Link and Farallon Skyline. It should also work on Symbol
+ * cards such as the 3Com AirConnect and Ericsson WLAN.
+ *
+ * Copyright (C) 2000 David Gibson, Linuxcare Australia <hermes@gibson.dropbear.id.au>
+ * With some help from :
+ * Copyright (C) 2001 Jean Tourrilhes, HP Labs <jt@hpl.hp.com>
+ * Copyright (C) 2001 Benjamin Herrenschmidt <benh@kernel.crashing.org>
+ *
+ * Based on dummy_cs.c 1.27 2000/06/12 21:27:25
+ *
+ * Portions based on wvlan_cs.c 1.0.6, Copyright Andreas Neuhaus <andy@fasta.fh-dortmund.de>
+ * http://www.fasta.fh-dortmund.de/users/andy/wvlan/
+ *
+ * The contents of this file are subject to the Mozilla Public License
+ * Version 1.1 (the "License"); you may not use this file except in
+ * compliance with the License. You may obtain a copy of the License
+ * at http://www.mozilla.org/MPL/
+ *
+ * Software distributed under the License is distributed on an "AS IS"
+ * basis, WITHOUT WARRANTY OF ANY KIND, either express or implied. See
+ * the License for the specific language governing rights and
+ * limitations under the License.
+ *
+ * The initial developer of the original code is David A. Hinds
+ * <dahinds@users.sourceforge.net>. Portions created by David
+ * A. Hinds are Copyright (C) 1999 David A. Hinds. All Rights
+ * Reserved.
+ *
+ * Alternatively, the contents of this file may be used under the
+ * terms of the GNU Public License version 2 (the "GPL"), in which
+ * case the provisions of the GPL are applicable instead of the above.
+ * If you wish to allow the use of your version of this file only
+ * under the terms of the GPL and not to allow others to use your
+ * version of this file under the MPL, indicate your decision by
+ * deleting the provisions above and replace them with the notice and
+ * other provisions required by the GPL. If you do not delete the
+ * provisions above, a recipient may use your version of this file
+ * under either the MPL or the GPL.
+ */
+
+/* Notes on locking:
+ *
+ * The basic principle of operation is that everything except the
+ * interrupt handler is serialized through a single spinlock in the
+ * dldwd_priv_t structure, using dldwd_lock() and
+ * dldwd_unlock() (which in turn use spin_lock_bh() and spin_unlock_bh()).
+ *
+ * The kernel's IRQ handling stuff ensures that the interrupt handler
+ * does not re-enter itself. The interrupt handler is written such
+ * that everything it does is safe without a lock: chiefly this means
+ * that the Rx path uses one of the Hermes chipset's BAPs while
+ * everything else uses the other.
+ *
+ * For the moment access to the device statistics from the interrupt
+ * handler is unsafe - we just put up with any resulting errors in the
+ * statisics. FIXME: This should probably be changed to store the
+ * stats in atomic types.
+ *
+ * EXCEPT that we don't want the irq handler running when we actually
+ * reset or shut down the card, because strange things might happen
+ * (probably the worst would be one packet of garbage, but you can't
+ * be too careful). For this we use __dldwd_stop_irqs() which will set
+ * a flag to disable the interrupt handler, and wait for any
+ * outstanding instances of the handler to complete. THIS WILL LOSE
+ * INTERRUPTS! so it shouldn't be used except for resets, when we
+ * don't care about that.*/
+
+/*
+ * Tentative changelog...
+ *
+ * v0.01 -> v0.02 - 21/3/2001 - Jean II
+ * o Allow to use regular ethX device name instead of dldwdX
+ * o Warning on IBSS with ESSID=any for firmware 6.06
+ * o Put proper range.throughput values (optimistic)
+ * o IWSPY support (IOCTL and stat gather in Rx path)
+ * o Allow setting frequency in Ad-Hoc mode
+ * o Disable WEP setting if !has_wep to work on old firmware
+ * o Fix txpower range
+ * o Start adding support for Samsung/Compaq firmware
+ *
+ * v0.02 -> v0.03 - 23/3/2001 - Jean II
+ * o Start adding Symbol support - need to check all that
+ * o Fix Prism2/Symbol WEP to accept 128 bits keys
+ * o Add Symbol WEP (add authentication type)
+ * o Add Prism2/Symbol rate
+ * o Add PM timeout (holdover duration)
+ * o Enable "iwconfig eth0 key off" and friends (toggle flags)
+ * o Enable "iwconfig eth0 power unicast/all" (toggle flags)
+ * o Try with an intel card. It report firmware 1.01, behave like
+ * an antiquated firmware, however on windows it says 2.00. Yuck !
+ * o Workaround firmware bug in allocate buffer (Intel 1.01)
+ * o Finish external renaming to orinoco...
+ * o Testing with various Wavelan firmwares
+ *
+ * v0.03 -> v0.04 - 30/3/2001 - Jean II
+ * o Update to Wireless 11 -> add retry limit/lifetime support
+ * o Tested with a D-Link DWL 650 card, fill in firmware support
+ * o Warning on Vcc mismatch (D-Link 3.3v card in Lucent 5v only slot)
+ * o Fixed the Prims2 WEP bugs that I introduced in v0.03 :-(
+ * It work on D-Link *only* after a tcpdump. Weird...
+ * And still doesn't work on Intel card. Grrrr...
+ * o Update the mode after a setport3
+ * o Add preamble setting for Symbol cards (not yet enabled)
+ * o Don't complain as much about Symbol cards...
+ *
+ * v0.04 -> v0.04b - 22/4/2001 - David Gibson
+ * o Removed the 'eth' parameter - always use ethXX as the
+ * interface name instead of dldwdXX. The other was racy
+ * anyway.
+ * o Clean up RID definitions in hermes.h, other cleanups
+ *
+ * v0.04b -> v0.04c - 24/4/2001 - Jean II
+ * o Tim Hurley <timster@seiki.bliztech.com> reported a D-Link card
+ * with vendor 02 and firmware 0.08. Added in the capabilities...
+ * o Tested Lucent firmware 7.28, everything works...
+ *
+ * v0.04c -> v0.05 - 3/5/2001 - Benjamin Herrenschmidt
+ * o Spin-off Pcmcia code. This file is renamed orinoco.c,
+ * and orinoco_cs.c now contains only the Pcmcia specific stuff
+ * o Add Airport driver support on top of orinoco.c (see airport.c)
+ *
+ * v0.05 -> v0.05a - 4/5/2001 - Jean II
+ * o Revert to old Pcmcia code to fix breakage of Ben's changes...
+ *
+ * v0.05a -> v0.05b - 4/5/2001 - Jean II
+ * o add module parameter 'ignore_cis_vcc' for D-Link @ 5V
+ * o D-Link firmware doesn't support multicast. We just print a few
+ * error messages, but otherwise everything works...
+ * o For David : set/getport3 works fine, just upgrade iwpriv...
+ *
+ * v0.05b -> v0.05c - 5/5/2001 - Benjamin Herrenschmidt
+ * o Adapt airport.c to latest changes in orinoco.c
+ * o Remove deferred power enabling code
+ *
+ * v0.05c -> v0.05d - 5/5/2001 - Jean II
+ * o Workaround to SNAP decapsulate frame from LinkSys AP
+ * original patch from : Dong Liu <dliu@research.bell-labs.com>
+ * (note : the memcmp bug was mine - fixed)
+ * o Remove set_retry stuff, no firmware support it (bloat--).
+ *
+ * TODO - Jean II
+ * o inline functions (lot's of candidate, need to reorder code)
+ * o Test PrismII/Symbol cards & firmware versions
+ * o Mini-PCI support
+ */
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/sched.h>
+#include <linux/ptrace.h>
+#include <linux/malloc.h>
+#include <linux/string.h>
+#include <linux/timer.h>
+#include <linux/ioport.h>
+#include <asm/uaccess.h>
+#include <asm/io.h>
+#include <asm/system.h>
+#include <linux/proc_fs.h>
+#include <linux/netdevice.h>
+#include <linux/if_arp.h>
+#include <linux/etherdevice.h>
+#include <linux/wireless.h>
+#include <linux/list.h>
+
+#include <pcmcia/version.h>
+#include <pcmcia/cs_types.h>
+#include <pcmcia/cs.h>
+#include <pcmcia/cistpl.h>
+#include <pcmcia/cisreg.h>
+#include <pcmcia/ds.h>
+#include <pcmcia/bus_ops.h>
+
+#include "hermes.h"
+#include "orinoco.h"
+
+static char *version = "orinoco.c 0.05d (David Gibson <hermes@gibson.dropbear.id.au> and others)";
+
+/* Level of debugging. Used in the macros in orinoco.h */
+#ifdef ORINOCO_DEBUG
+int dldwd_debug = ORINOCO_DEBUG;
+MODULE_PARM(dldwd_debug, "i");
+#endif
+
+const long channel_frequency[] = {
+ 2412, 2417, 2422, 2427, 2432, 2437, 2442,
+ 2447, 2452, 2457, 2462, 2467, 2472, 2484
+};
+
+#define NUM_CHANNELS ( sizeof(channel_frequency) / sizeof(channel_frequency[0]) )
+
+/* This tables gives the actual meanings of the bitrate IDs returned by the firmware.
+ It gives the rate in halfMb/s, negative indicates auto mode */
+const int rate_list[] = { 0, 2, 4, -22, 11, 22, -4, -11, 0, 0, 0, 0};
+
+#define NUM_RATES (sizeof(rate_list) / sizeof(rate_list[0]))
+
+struct p80211_hdr {
+ uint16_t frame_ctl;
+ uint16_t duration_id;
+ uint8_t addr1[ETH_ALEN];
+ uint8_t addr2[ETH_ALEN];
+ uint8_t addr3[ETH_ALEN];
+ uint16_t seq_ctl;
+ uint8_t addr4[ETH_ALEN];
+ uint16_t data_len;
+} __attribute__ ((packed));
+
+/* Frame control field constants */
+#define DLDWD_FCTL_VERS 0x0002
+#define DLDWD_FCTL_FTYPE 0x000c
+#define DLDWD_FCTL_STYPE 0x00f0
+#define DLDWD_FCTL_TODS 0x0100
+#define DLDWD_FCTL_FROMDS 0x0200
+#define DLDWD_FCTL_MOREFRAGS 0x0400
+#define DLDWD_FCTL_RETRY 0x0800
+#define DLDWD_FCTL_PM 0x1000
+#define DLDWD_FCTL_MOREDATA 0x2000
+#define DLDWD_FCTL_WEP 0x4000
+#define DLDWD_FCTL_ORDER 0x8000
+
+#define DLDWD_FTYPE_MGMT 0x0000
+#define DLDWD_FTYPE_CTL 0x0004
+#define DLDWD_FTYPE_DATA 0x0008
+
+struct p8022_hdr {
+ uint8_t dsap;
+ uint8_t ssap;
+ uint8_t ctrl;
+ uint8_t oui[3];
+} __attribute__ ((packed));
+
+struct dldwd_frame_hdr {
+ hermes_frame_desc_t desc;
+ struct p80211_hdr p80211;
+ struct ethhdr p8023;
+ struct p8022_hdr p8022;
+ uint16_t ethertype;
+} __attribute__ ((packed));
+
+#define P8023_OFFSET (sizeof(hermes_frame_desc_t) + \
+ sizeof(struct p80211_hdr))
+#define ENCAPS_OVERHEAD (sizeof(struct p8022_hdr) + 2)
+
+/* 802.2 LLL header SNAP used for SNAP encapsulation over 802.11 */
+struct p8022_hdr encaps_hdr = {
+ 0xaa, 0xaa, 0x03, {0x00, 0x00, 0xf8}
+};
+
+/*
+ * Function prototypes
+ */
+
+static void dldwd_stat_gather(struct net_device *dev,
+ struct sk_buff *skb,
+ struct dldwd_frame_hdr *hdr);
+
+static struct net_device_stats *dldwd_get_stats(struct net_device *dev);
+static struct iw_statistics *dldwd_get_wireless_stats(struct net_device *dev);
+
+/* Hardware control routines */
+
+static int __dldwd_hw_reset(dldwd_priv_t *priv);
+static int __dldwd_hw_setup_wep(dldwd_priv_t *priv);
+static int dldwd_hw_get_bssid(dldwd_priv_t *priv, char buf[ETH_ALEN]);
+static int dldwd_hw_get_essid(dldwd_priv_t *priv, int *active, char buf[IW_ESSID_MAX_SIZE+1]);
+static long dldwd_hw_get_freq(dldwd_priv_t *priv);
+static int dldwd_hw_get_bitratelist(dldwd_priv_t *priv, int *numrates,
+ int32_t *rates, int max);
+
+/* Interrupt handling routines */
+static void __dldwd_ev_tick(dldwd_priv_t *priv, hermes_t *hw);
+static void __dldwd_ev_wterr(dldwd_priv_t *priv, hermes_t *hw);
+static void __dldwd_ev_infdrop(dldwd_priv_t *priv, hermes_t *hw);
+static void __dldwd_ev_info(dldwd_priv_t *priv, hermes_t *hw);
+static void __dldwd_ev_rx(dldwd_priv_t *priv, hermes_t *hw);
+static void __dldwd_ev_txexc(dldwd_priv_t *priv, hermes_t *hw);
+static void __dldwd_ev_tx(dldwd_priv_t *priv, hermes_t *hw);
+static void __dldwd_ev_alloc(dldwd_priv_t *priv, hermes_t *hw);
+
+static int dldwd_ioctl_getiwrange(struct net_device *dev, struct iw_point *rrq);
+static int dldwd_ioctl_setiwencode(struct net_device *dev, struct iw_point *erq);
+static int dldwd_ioctl_getiwencode(struct net_device *dev, struct iw_point *erq);
+static int dldwd_ioctl_setessid(struct net_device *dev, struct iw_point *erq);
+static int dldwd_ioctl_getessid(struct net_device *dev, struct iw_point *erq);
+static int dldwd_ioctl_setnick(struct net_device *dev, struct iw_point *nrq);
+static int dldwd_ioctl_getnick(struct net_device *dev, struct iw_point *nrq);
+static int dldwd_ioctl_setfreq(struct net_device *dev, struct iw_freq *frq);
+static int dldwd_ioctl_getsens(struct net_device *dev, struct iw_param *srq);
+static int dldwd_ioctl_setsens(struct net_device *dev, struct iw_param *srq);
+static int dldwd_ioctl_setrts(struct net_device *dev, struct iw_param *rrq);
+static int dldwd_ioctl_setfrag(struct net_device *dev, struct iw_param *frq);
+static int dldwd_ioctl_getfrag(struct net_device *dev, struct iw_param *frq);
+static int dldwd_ioctl_setrate(struct net_device *dev, struct iw_param *frq);
+static int dldwd_ioctl_getrate(struct net_device *dev, struct iw_param *frq);
+static int dldwd_ioctl_setpower(struct net_device *dev, struct iw_param *prq);
+static int dldwd_ioctl_getpower(struct net_device *dev, struct iw_param *prq);
+static int dldwd_ioctl_setport3(struct net_device *dev, struct iwreq *wrq);
+static int dldwd_ioctl_getport3(struct net_device *dev, struct iwreq *wrq);
+static void __dldwd_set_multicast_list(struct net_device *dev);
+
+/* /proc debugging stuff */
+static int dldwd_proc_init(void);
+static void dldwd_proc_cleanup(void);
+
+/*
+ * Inline functions
+ */
+static inline void
+dldwd_lock(dldwd_priv_t *priv)
+{
+ spin_lock_bh(&priv->lock);
+}
+
+static inline void
+dldwd_unlock(dldwd_priv_t *priv)
+{
+ spin_unlock_bh(&priv->lock);
+}
+
+static inline int
+dldwd_irqs_allowed(dldwd_priv_t *priv)
+{
+ return test_bit(DLDWD_STATE_DOIRQ, &priv->state);
+}
+
+static inline void
+__dldwd_stop_irqs(dldwd_priv_t *priv)
+{
+ hermes_t *hw = &priv->hw;
+
+ hermes_set_irqmask(hw, 0);
+ clear_bit(DLDWD_STATE_DOIRQ, &priv->state);
+ while (test_bit(DLDWD_STATE_INIRQ, &priv->state))
+ ;
+}
+
+static inline void
+__dldwd_start_irqs(dldwd_priv_t *priv, uint16_t irqmask)
+{
+ hermes_t *hw = &priv->hw;
+
+ TRACE_ENTER(priv->ndev.name);
+
+ __cli();
+ set_bit(DLDWD_STATE_DOIRQ, &priv->state);
+ hermes_set_irqmask(hw, irqmask);
+ __sti();
+
+ TRACE_EXIT(priv->ndev.name);
+}
+
+static inline void
+set_port_type(dldwd_priv_t *priv)
+{
+ switch (priv->iw_mode) {
+ case IW_MODE_INFRA:
+ priv->port_type = 1;
+ priv->allow_ibss = 0;
+ break;
+ case IW_MODE_ADHOC:
+ if (priv->prefer_port3) {
+ priv->port_type = 3;
+ priv->allow_ibss = 0;
+ } else {
+ priv->port_type = 1;
+ priv->allow_ibss = 1;
+ }
+ break;
+ default:
+ printk(KERN_ERR "%s: Invalid priv->iw_mode in set_port_type()\n",
+ priv->ndev.name);
+ }
+}
+
+extern void
+dldwd_set_multicast_list(struct net_device *dev)
+{
+ dldwd_priv_t *priv = dev->priv;
+
+ dldwd_lock(priv);
+ __dldwd_set_multicast_list(dev);
+ dldwd_unlock(priv);
+}
+
+/*
+ * Hardware control routines
+ */
+
+static int
+__dldwd_hw_reset(dldwd_priv_t *priv)
+{
+ hermes_t *hw = &priv->hw;
+ int err;
+
+ if (! priv->broken_reset)
+ return hermes_reset(hw);
+ else {
+ hw->inten = 0;
+ hermes_write_regn(hw, INTEN, 0);
+ err = hermes_disable_port(hw, 0);
+ hermes_write_regn(hw, EVACK, 0xffff);
+ return err;
+ }
+}
+
+void
+dldwd_shutdown(dldwd_priv_t *priv)
+{
+/* hermes_t *hw = &priv->hw; */
+ int err = 0;
+
+ TRACE_ENTER(priv->ndev.name);
+
+ dldwd_lock(priv);
+ __dldwd_stop_irqs(priv);
+
+ err = __dldwd_hw_reset(priv);
+ if (err && err != -ENODEV) /* If the card is gone, we don't care about shutting it down */
+ printk(KERN_ERR "%s: Error %d shutting down Hermes chipset\n", priv->ndev.name, err);
+
+ dldwd_unlock(priv);
+
+ TRACE_EXIT(priv->ndev.name);
+}
+
+int
+dldwd_reset(dldwd_priv_t *priv)
+{
+ struct net_device *dev = &priv->ndev;
+ hermes_t *hw = &priv->hw;
+ int err = 0;
+ hermes_id_t idbuf;
+ int frame_size;
+
+ TRACE_ENTER(priv->ndev.name);
+
+ dldwd_lock(priv);
+
+ __dldwd_stop_irqs(priv);
+
+ err = __dldwd_hw_reset(priv);
+ if (err)
+ goto out;
+
+ frame_size = TX_NICBUF_SIZE;
+ /* This stupid bug is present in Intel firmware 1.10, and
+ * may be fixed in later firmwares - Jean II */
+ if(priv->broken_allocate)
+ frame_size = TX_NICBUF_SIZE_BUG;
+ err = hermes_allocate(hw, frame_size, &priv->txfid);
+ if (err)
+ goto out;
+
+ /* Now set up all the parameters on the card */
+
+ /* Set up the link mode */
+
+ err = hermes_write_wordrec(hw, USER_BAP, HERMES_RID_CNF_PORTTYPE, priv->port_type);
+ if (err)
+ goto out;
+ if (priv->has_ibss) {
+ err = hermes_write_wordrec(hw, USER_BAP, HERMES_RID_CNF_CREATEIBSS,
+ priv->allow_ibss);
+ if (err)
+ goto out;
+ if((strlen(priv->desired_essid) == 0) && (priv->allow_ibss)
+ && (!priv->has_ibss_any)) {
+ printk(KERN_WARNING "%s: This firmware requires an \
+ESSID in IBSS-Ad-Hoc mode.\n", dev->name);
+ /* With wvlan_cs, in this case, we would crash.
+ * hopefully, this driver will behave better...
+ * Jean II */
+ }
+ }
+
+ /* Set up encryption */
+ if (priv->has_wep) {
+ err = __dldwd_hw_setup_wep(priv);
+ if (err)
+ goto out;
+ }
+
+ /* Set the desired ESSID */
+ idbuf.len = cpu_to_le16(strlen(priv->desired_essid));
+ memcpy(&idbuf.val, priv->desired_essid, sizeof(idbuf.val));
+ err = hermes_write_ltv(hw, USER_BAP, (priv->port_type == 3) ?
+ HERMES_RID_CNF_OWN_SSID : HERMES_RID_CNF_DESIRED_SSID,
+ HERMES_BYTES_TO_RECLEN(strlen(priv->desired_essid)+2),
+ &idbuf);
+ if (err)
+ goto out;
+
+ /* Set the station name */
+ idbuf.len = cpu_to_le16(strlen(priv->nick));
+ memcpy(&idbuf.val, priv->nick, sizeof(idbuf.val));
+ err = hermes_write_ltv(hw, USER_BAP, HERMES_RID_CNF_NICKNAME,
+ HERMES_BYTES_TO_RECLEN(strlen(priv->nick)+2),
+ &idbuf);
+ if (err)
+ goto out;
+
+ /* Set the channel/frequency */
+ err = hermes_write_wordrec(hw, USER_BAP, HERMES_RID_CNF_CHANNEL, priv->channel);
+ if (err)
+ goto out;
+
+ /* Set AP density */
+ err = hermes_write_wordrec(hw, USER_BAP, HERMES_RID_CNF_SYSTEM_SCALE, priv->ap_density);
+ if (err)
+ goto out;
+
+ /* Set RTS threshold */
+ err = hermes_write_wordrec(hw, USER_BAP, HERMES_RID_CNF_RTS_THRESH, priv->rts_thresh);
+ if (err)
+ goto out;
+
+ /* Set fragmentation threshold or MWO robustness */
+ if (priv->has_mwo)
+ err = hermes_write_wordrec(hw, USER_BAP,
+ HERMES_RID_CNF_MWO_ROBUST, priv->mwo_robust);
+ else
+ err = hermes_write_wordrec(hw, USER_BAP,
+ HERMES_RID_CNF_FRAG_THRESH, priv->frag_thresh);
+ if (err)
+ goto out;
+
+ /* Set bitrate */
+ err = hermes_write_wordrec(hw, USER_BAP, HERMES_RID_CNF_TX_RATE_CTRL,
+ priv->tx_rate_ctrl);
+ if (err)
+ goto out;
+
+ /* Set power management */
+ if (priv->has_pm) {
+ err = hermes_write_wordrec(hw, USER_BAP, HERMES_RID_CNF_PM_ENABLE,
+ priv->pm_on);
+ if (err)
+ goto out;
+ err = hermes_write_wordrec(hw, USER_BAP, HERMES_RID_CNF_PM_MCAST_RX,
+ priv->pm_mcast);
+ if (err)
+ goto out;
+ err = hermes_write_wordrec(hw, USER_BAP, HERMES_RID_CNF_PM_PERIOD,
+ priv->pm_period);
+ if (err)
+ goto out;
+ err = hermes_write_wordrec(hw, USER_BAP, HERMES_RID_CNF_PM_HOLDOVER,
+ priv->pm_timeout);
+ if (err)
+ goto out;
+ }
+
+ /* Set preamble - only for Symbol so far... */
+ if (priv->has_preamble) {
+ err = hermes_write_wordrec(hw, USER_BAP, HERMES_RID_CNF_SYMBOL_PREAMBLE,
+ priv->preamble);
+ if (err) {
+ printk(KERN_WARNING "%s: Can't set preamble!\n", dev->name);
+ goto out;
+ }
+ }
+
+ /* Set promiscuity / multicast*/
+ priv->promiscuous = 0;
+ priv->allmulti = 0;
+ priv->mc_count = 0;
+ __dldwd_set_multicast_list(dev);
+
+ err = hermes_enable_port(hw, DLDWD_MACPORT);
+ if (err)
+ goto out;
+
+ __dldwd_start_irqs(priv, HERMES_EV_RX | HERMES_EV_ALLOC |
+ HERMES_EV_TX | HERMES_EV_TXEXC |
+ HERMES_EV_WTERR | HERMES_EV_INFO |
+ HERMES_EV_INFDROP);
+
+ out:
+ dldwd_unlock(priv);
+
+ TRACE_EXIT(priv->ndev.name);
+
+ return err;
+}
+
+static int __dldwd_hw_setup_wep(dldwd_priv_t *priv)
+{
+ hermes_t *hw = &priv->hw;
+ int err = 0;
+ int extra_wep_flag = 0;
+
+ switch (priv->firmware_type) {
+ case FIRMWARE_TYPE_LUCENT: /* Lucent style WEP */
+ if (priv->wep_on) {
+ err = hermes_write_wordrec(hw, USER_BAP, HERMES_RID_CNF_TX_KEY, priv->tx_key);
+ if (err)
+ return err;
+
+ err = HERMES_WRITE_RECORD(hw, USER_BAP, HERMES_RID_CNF_KEYS, &priv->keys);
+ if (err)
+ return err;
+ }
+ err = hermes_write_wordrec(hw, USER_BAP, HERMES_RID_CNF_WEP_ON, priv->wep_on);
+ if (err)
+ return err;
+ break;
+
+ case FIRMWARE_TYPE_PRISM2: /* Prism II style WEP */
+ case FIRMWARE_TYPE_SYMBOL: /* Symbol style WEP */
+ if (priv->wep_on) {
+ char keybuf[LARGE_KEY_SIZE+1];
+ int keylen;
+ int i;
+
+ /* Write all 4 keys */
+ for(i = 0; i < MAX_KEYS; i++) {
+ keylen = priv->keys[i].len;
+ keybuf[keylen] = '\0';
+ memcpy(keybuf, priv->keys[i].data, keylen);
+ err = hermes_write_ltv(hw, USER_BAP,
+ HERMES_RID_CNF_PRISM2_KEY0 + i,
+ HERMES_BYTES_TO_RECLEN(keylen + 1),
+ &keybuf);
+ if (err)
+ return err;
+ }
+
+ err = hermes_write_wordrec(hw, USER_BAP, HERMES_RID_CNF_PRISM2_TX_KEY,
+ priv->tx_key);
+ if (err)
+ return err;
+
+ /* Authentication is where Prism2 and Symbol
+ * firmware differ... */
+ if (priv->firmware_type == FIRMWARE_TYPE_SYMBOL) {
+ /* Symbol cards : set the authentication :
+ * 0 -> no encryption, 1 -> open,
+ * 2 -> shared key, 3 -> shared key 128bit */
+ if(priv->wep_restrict) {
+ if(priv->keys[priv->tx_key].len >
+ SMALL_KEY_SIZE)
+ extra_wep_flag = 3;
+ else
+ extra_wep_flag = 2;
+ } else
+ extra_wep_flag = 1;
+ err = hermes_write_wordrec(hw, USER_BAP, HERMES_RID_CNF_SYMBOL_AUTH_TYPE, priv->wep_restrict);
+ if (err)
+ return err;
+ } else {
+ /* Prism2 card : we need to modify master
+ * WEP setting */
+ if(priv->wep_restrict)
+ extra_wep_flag = 2;
+ else
+ extra_wep_flag = 0;
+ }
+ }
+
+ /* Master WEP setting : on/off */
+ err = hermes_write_wordrec(hw, USER_BAP, HERMES_RID_CNF_PRISM2_WEP_ON, (priv->wep_on | extra_wep_flag));
+ if (err)
+ return err;
+ break;
+
+ default:
+ if (priv->wep_on) {
+ printk(KERN_ERR "%s: WEP enabled, although not supported!\n",
+ priv->ndev.name);
+ return -EINVAL;
+ }
+ }
+
+ return 0;
+}
+
+static int dldwd_hw_get_bssid(dldwd_priv_t *priv, char buf[ETH_ALEN])
+{
+ hermes_t *hw = &priv->hw;
+ int err = 0;
+
+ dldwd_lock(priv);
+
+ err = hermes_read_ltv(hw, USER_BAP, HERMES_RID_CURRENT_BSSID,
+ ETH_ALEN, NULL, buf);
+
+ dldwd_unlock(priv);
+
+ return err;
+}
+
+static int dldwd_hw_get_essid(dldwd_priv_t *priv, int *active,
+ char buf[IW_ESSID_MAX_SIZE+1])
+{
+ hermes_t *hw = &priv->hw;
+ int err = 0;
+ hermes_id_t essidbuf;
+ char *p = (char *)(&essidbuf.val);
+ int len;
+
+ TRACE_ENTER(priv->ndev.name);
+
+ dldwd_lock(priv);
+
+ if (strlen(priv->desired_essid) > 0) {
+ /* We read the desired SSID from the hardware rather
+ than from priv->desired_essid, just in case the
+ firmware is allowed to change it on us. I'm not
+ sure about this */
+ /* My guess is that the OWN_SSID should always be whatever
+ * we set to the card, whereas CURRENT_SSID is the one that
+ * may change... - Jean II */
+ uint16_t rid;
+
+ *active = 1;
+
+ rid = (priv->port_type == 3) ? HERMES_RID_CNF_OWN_SSID :
+ HERMES_RID_CNF_DESIRED_SSID;
+
+ err = hermes_read_ltv(hw, USER_BAP, rid, sizeof(essidbuf),
+ NULL, &essidbuf);
+ if (err)
+ goto fail_unlock;
+ } else {
+ *active = 0;
+
+ err = hermes_read_ltv(hw, USER_BAP, HERMES_RID_CURRENT_SSID,
+ sizeof(essidbuf), NULL, &essidbuf);
+ if (err)
+ goto fail_unlock;
+ }
+
+ len = le16_to_cpu(essidbuf.len);
+
+ memset(buf, 0, sizeof(buf));
+ memcpy(buf, p, len);
+ buf[len] = '\0';
+
+ fail_unlock:
+ dldwd_unlock(priv);
+
+ TRACE_EXIT(priv->ndev.name);
+
+ return err;
+}
+
+static long dldwd_hw_get_freq(dldwd_priv_t *priv)
+{
+
+ hermes_t *hw = &priv->hw;
+ int err = 0;
+ uint16_t channel;
+ long freq = 0;
+
+ dldwd_lock(priv);
+
+ err = hermes_read_wordrec(hw, USER_BAP, HERMES_RID_CURRENT_CHANNEL, &channel);
+ if (err)
+ goto out;
+
+ if ( (channel < 1) || (channel > NUM_CHANNELS) ) {
+ struct net_device *dev = &priv->ndev;
+
+ printk(KERN_WARNING "%s: Channel out of range (%d)!\n", dev->name, channel);
+ err = -EBUSY;
+ goto out;
+
+ }
+ freq = channel_frequency[channel-1] * 100000;
+
+ out:
+ dldwd_unlock(priv);
+
+ if (err > 0)
+ err = -EBUSY;
+ return err ? err : freq;
+}
+
+static int dldwd_hw_get_bitratelist(dldwd_priv_t *priv, int *numrates,
+ int32_t *rates, int max)
+{
+ hermes_t *hw = &priv->hw;
+ hermes_id_t list;
+ unsigned char *p = (unsigned char *)&list.val;
+ int err = 0;
+ int num;
+ int i;
+
+ dldwd_lock(priv);
+ err = hermes_read_ltv(hw, USER_BAP, HERMES_RID_DATARATES, sizeof(list),
+ NULL, &list);
+ dldwd_unlock(priv);
+
+ if (err)
+ return err;
+
+ num = le16_to_cpu(list.len);
+ *numrates = num;
+ num = MIN(num, max);
+
+ for (i = 0; i < num; i++) {
+ rates[i] = (p[i] & 0x7f) * 500000; /* convert to bps */
+ }
+
+ return 0;
+}
+
+#ifndef PCMCIA_DEBUG
+static inline void show_rx_frame(struct dldwd_frame_hdr *frame) {}
+#else
+static void show_rx_frame(struct dldwd_frame_hdr *frame)
+{
+ printk(KERN_DEBUG "RX descriptor:\n");
+ printk(KERN_DEBUG " status = 0x%04x\n", frame->desc.status);
+ printk(KERN_DEBUG " res1 = 0x%04x\n", frame->desc.res1);
+ printk(KERN_DEBUG " res2 = 0x%04x\n", frame->desc.res2);
+ printk(KERN_DEBUG " q_info = 0x%04x\n", frame->desc.q_info);
+ printk(KERN_DEBUG " res3 = 0x%04x\n", frame->desc.res3);
+ printk(KERN_DEBUG " res4 = 0x%04x\n", frame->desc.res4);
+ printk(KERN_DEBUG " tx_ctl = 0x%04x\n", frame->desc.tx_ctl);
+
+ printk(KERN_DEBUG "IEEE 802.11 header:\n");
+ printk(KERN_DEBUG " frame_ctl = 0x%04x\n",
+ frame->p80211.frame_ctl);
+ printk(KERN_DEBUG " duration_id = 0x%04x\n",
+ frame->p80211.duration_id);
+ printk(KERN_DEBUG " addr1 = %02x:%02x:%02x:%02x:%02x:%02x\n",
+ frame->p80211.addr1[0], frame->p80211.addr1[1],
+ frame->p80211.addr1[2], frame->p80211.addr1[3],
+ frame->p80211.addr1[4], frame->p80211.addr1[5]);
+ printk(KERN_DEBUG " addr2 = %02x:%02x:%02x:%02x:%02x:%02x\n",
+ frame->p80211.addr2[0], frame->p80211.addr2[1],
+ frame->p80211.addr2[2], frame->p80211.addr2[3],
+ frame->p80211.addr2[4], frame->p80211.addr2[5]);
+ printk(KERN_DEBUG " addr3 = %02x:%02x:%02x:%02x:%02x:%02x\n",
+ frame->p80211.addr3[0], frame->p80211.addr3[1],
+ frame->p80211.addr3[2], frame->p80211.addr3[3],
+ frame->p80211.addr3[4], frame->p80211.addr3[5]);
+ printk(KERN_DEBUG " seq_ctl = 0x%04x\n",
+ frame->p80211.seq_ctl);
+ printk(KERN_DEBUG " addr4 = %02x:%02x:%02x:%02x:%02x:%02x\n",
+ frame->p80211.addr4[0], frame->p80211.addr4[1],
+ frame->p80211.addr4[2], frame->p80211.addr4[3],
+ frame->p80211.addr4[4], frame->p80211.addr4[5]);
+ printk(KERN_DEBUG " data_len = 0x%04x\n",
+ frame->p80211.data_len);
+
+ printk(KERN_DEBUG "IEEE 802.3 header:\n");
+ printk(KERN_DEBUG " dest = %02x:%02x:%02x:%02x:%02x:%02x\n",
+ frame->p8023.h_dest[0], frame->p8023.h_dest[1],
+ frame->p8023.h_dest[2], frame->p8023.h_dest[3],
+ frame->p8023.h_dest[4], frame->p8023.h_dest[5]);
+ printk(KERN_DEBUG " src = %02x:%02x:%02x:%02x:%02x:%02x\n",
+ frame->p8023.h_source[0], frame->p8023.h_source[1],
+ frame->p8023.h_source[2], frame->p8023.h_source[3],
+ frame->p8023.h_source[4], frame->p8023.h_source[5]);
+ printk(KERN_DEBUG " len = 0x%04x\n", frame->p8023.h_proto);
+
+ printk(KERN_DEBUG "IEEE 802.2 LLC/SNAP header:\n");
+ printk(KERN_DEBUG " DSAP = 0x%02x\n", frame->p8022.dsap);
+ printk(KERN_DEBUG " SSAP = 0x%02x\n", frame->p8022.ssap);
+ printk(KERN_DEBUG " ctrl = 0x%02x\n", frame->p8022.ctrl);
+ printk(KERN_DEBUG " OUI = %02x:%02x:%02x\n",
+ frame->p8022.oui[0], frame->p8022.oui[1], frame->p8022.oui[2]);
+ printk(KERN_DEBUG " ethertype = 0x%04x\n", frame->ethertype);
+}
+#endif
+
+/*
+ * Interrupt handler
+ */
+void dldwd_interrupt(int irq, void * dev_id, struct pt_regs *regs)
+{
+ dldwd_priv_t *priv = (dldwd_priv_t *) dev_id;
+ hermes_t *hw = &priv->hw;
+ struct net_device *dev = &priv->ndev;
+ int count = IRQ_LOOP_MAX;
+ uint16_t evstat, events;
+ static int old_time = 0, timecount = 0; /* Eugh, revolting hack for now */
+
+ if (test_and_set_bit(DLDWD_STATE_INIRQ, &priv->state))
+ BUG();
+
+ if (! dldwd_irqs_allowed(priv)) {
+ clear_bit(DLDWD_STATE_INIRQ, &priv->state);
+ return;
+ }
+
+ DEBUG(3, "%s: dldwd_interrupt()\n", priv->ndev.name);
+
+ while (1) {
+ if (jiffies != old_time)
+ timecount = 0;
+ if ( (++timecount > 50) || (! count--) ) {
+ printk(KERN_CRIT "%s: IRQ handler is looping too \
+much! Shutting down.\n",
+ dev->name);
+ /* Perform an emergency shutdown */
+ clear_bit(DLDWD_STATE_DOIRQ, &priv->state);
+ hermes_set_irqmask(hw, 0);
+ break;
+ }
+
+ evstat = hermes_read_regn(hw, EVSTAT);
+ DEBUG(3, "__dldwd_interrupt(): count=%d EVSTAT=0x%04x inten=0x%04x\n",
+ count, evstat, hw->inten);
+
+ events = evstat & hw->inten;
+
+ if (! events) {
+ if (netif_queue_stopped(dev)) {
+ /* There seems to be a firmware bug which
+ sometimes causes the card to give an
+ interrupt with no event set, when there
+ sould be a Tx completed event. */
+ DEBUG(3, "%s: Interrupt with no event (ALLOCFID=0x%04x)\n",
+ dev->name, (int)hermes_read_regn(hw, ALLOCFID));
+ events = HERMES_EV_TX | HERMES_EV_ALLOC;
+ } else /* Nothing's happening, we're done */
+ break;
+ }
+
+ /* Check the card hasn't been removed */
+ if (! hermes_present(hw)) {
+ DEBUG(0, "dldwd_interrupt(): card removed\n");
+ break;
+ }
+
+ if (events & HERMES_EV_TICK)
+ __dldwd_ev_tick(priv, hw);
+ if (events & HERMES_EV_WTERR)
+ __dldwd_ev_wterr(priv, hw);
+ if (events & HERMES_EV_INFDROP)
+ __dldwd_ev_infdrop(priv, hw);
+ if (events & HERMES_EV_INFO)
+ __dldwd_ev_info(priv, hw);
+ if (events & HERMES_EV_RX)
+ __dldwd_ev_rx(priv, hw);
+ if (events & HERMES_EV_TXEXC)
+ __dldwd_ev_txexc(priv, hw);
+ if (events & HERMES_EV_TX)
+ __dldwd_ev_tx(priv, hw);
+ if (events & HERMES_EV_ALLOC)
+ __dldwd_ev_alloc(priv, hw);
+
+ hermes_write_regn(hw, EVACK, events);
+ }
+
+ clear_bit(DLDWD_STATE_INIRQ, &priv->state);
+}
+
+static void __dldwd_ev_tick(dldwd_priv_t *priv, hermes_t *hw)
+{
+ printk(KERN_DEBUG "%s: TICK\n", priv->ndev.name);
+}
+
+static void __dldwd_ev_wterr(dldwd_priv_t *priv, hermes_t *hw)
+{
+ /* This seems to happen a fair bit under load, but ignoring it
+ seems to work fine...*/
+ DEBUG(1, "%s: MAC controller error (WTERR). Ignoring.\n",
+ priv->ndev.name);
+}
+
+static void __dldwd_ev_infdrop(dldwd_priv_t *priv, hermes_t *hw)
+{
+ printk(KERN_WARNING "%s: Information frame lost.\n", priv->ndev.name);
+}
+
+static void __dldwd_ev_info(dldwd_priv_t *priv, hermes_t *hw)
+{
+ DEBUG(3, "%s: Information frame received.\n", priv->ndev.name);
+ /* We don't actually do anything about it - we assume the MAC
+ controller can deal with it */
+}
+
+static void __dldwd_ev_rx(dldwd_priv_t *priv, hermes_t *hw)
+{
+ struct net_device *dev = &priv->ndev;
+ struct net_device_stats *stats = &priv->stats;
+ struct iw_statistics *wstats = &priv->wstats;
+ struct sk_buff *skb = NULL;
+ uint16_t rxfid, status;
+ int length, data_len, data_off;
+ char *p;
+ struct dldwd_frame_hdr hdr;
+ struct ethhdr *eh;
+ int err;
+
+ rxfid = hermes_read_regn(hw, RXFID);
+ DEBUG(3, "__dldwd_ev_rx(): RXFID=0x%04x\n", rxfid);
+
+ /* We read in the entire frame header here. This isn't really
+ necessary, since we ignore most of it, but it's
+ conceptually simpler. We can tune this later if
+ necessary. */
+ err = hermes_bap_pread(hw, IRQ_BAP, &hdr, sizeof(hdr), rxfid, 0);
+ if (err) {
+ printk(KERN_ERR "%s: error %d reading frame header. "
+ "Frame dropped.\n", dev->name, err);
+ stats->rx_errors++;
+ goto drop;
+ }
+
+ status = le16_to_cpu(hdr.desc.status);
+
+ if (status & HERMES_RXSTAT_ERR) {
+ if ((status & HERMES_RXSTAT_ERR) == HERMES_RXSTAT_BADCRC) {
+ stats->rx_crc_errors++;
+ printk(KERN_WARNING "%s: Bad CRC on Rx. Frame dropped.\n",
+ dev->name);
+ show_rx_frame(&hdr);
+ } else if ((status & HERMES_RXSTAT_ERR)
+ == HERMES_RXSTAT_UNDECRYPTABLE) {
+ wstats->discard.code++;
+ printk(KERN_WARNING "%s: Undecryptable frame on Rx. Frame dropped.\n",
+ dev->name);
+ } else {
+ wstats->discard.misc++;
+ printk("%s: Unknown Rx error (0x%x). Frame dropped.\n",
+ dev->name, status & HERMES_RXSTAT_ERR);
+ }
+ stats->rx_errors++;
+ goto drop;
+ }
+
+ length = le16_to_cpu(hdr.p80211.data_len);
+ /* Yes, you heard right, that's le16. 802.2 and 802.3 are
+ big-endian, but 802.11 is little-endian believe it or
+ not. */
+ /* Correct. 802.3 is big-endian byte order and little endian bit
+ * order, whereas 802.11 is little endian for both byte and bit
+ * order. That's specified in the 802.11 spec. - Jean II */
+
+ /* Sanity check */
+ if (length > MAX_FRAME_SIZE) {
+ printk(KERN_WARNING "%s: Oversized frame received (%d bytes)\n",
+ dev->name, length);
+ stats->rx_length_errors++;
+ stats->rx_errors++;
+ goto drop;
+ }
+
+ /* We need space for the packet data itself, plus an ethernet
+ header, plus 2 bytes so we can align the IP header on a
+ 32bit boundary, plus 1 byte so we can read in odd length
+ packets from the card, which has an IO granularity of 16
+ bits */
+ skb = dev_alloc_skb(length+ETH_HLEN+2+1);
+ if (!skb) {
+ printk(KERN_WARNING "%s: Can't allocate skb for Rx\n",
+ dev->name);
+ stats->rx_dropped++;
+ goto drop;
+ }
+
+ skb_reserve(skb, 2); /* This way the IP header is aligned */
+
+ /* Handle decapsulation
+ * In most cases, the firmware tell us about SNAP frames.
+ * For some reason, the SNAP frames sent by LinkSys APs
+ * are not properly recognised by most firmwares.
+ * So, check ourselves (note : only 3 bytes out of 6).
+ */
+ if(((status & HERMES_RXSTAT_MSGTYPE) == HERMES_RXSTAT_1042) ||
+ ((status & HERMES_RXSTAT_MSGTYPE) == HERMES_RXSTAT_TUNNEL) ||
+ (!memcmp(&hdr.p8022, &encaps_hdr, 3))) {
+ /* These indicate a SNAP within 802.2 LLC within
+ 802.11 frame which we'll need to de-encapsulate to
+ the original EthernetII frame.
+ IEEE and ISO OSI have a lot to answer for. */
+
+ /* Remove SNAP header, reconstruct EthernetII frame */
+ data_len = length - ENCAPS_OVERHEAD;
+ data_off = sizeof(hdr);
+
+ eh = (struct ethhdr *)skb_put(skb, ETH_HLEN);
+
+ memcpy(eh, &hdr.p8023, sizeof(hdr.p8023));
+ eh->h_proto = hdr.ethertype;
+ } else {
+ /* All other cases indicate a genuine 802.3 frame.
+ * No decapsulation needed */
+
+ /* Otherwise, we just throw the whole thing in,
+ * and hope the protocol layer can deal with it
+ * as 802.3 */
+ data_len = length;
+ data_off = P8023_OFFSET;
+ }
+
+ p = skb_put(skb, data_len);
+ if (hermes_bap_pread(hw, IRQ_BAP, p, RUP_EVEN(data_len),
+ rxfid, data_off) != 0) {
+ printk(KERN_WARNING "%s: Error reading packet data\n",
+ dev->name);
+ stats->rx_errors++;
+ goto drop;
+ }
+
+ dev->last_rx = jiffies;
+ skb->dev = dev;
+ skb->protocol = eth_type_trans(skb, dev);
+ skb->ip_summed = CHECKSUM_NONE;
+
+ /* Process the wireless stats if needed */
+ dldwd_stat_gather(dev, skb, &hdr);
+
+ /* Pass the packet to the networking stack */
+ netif_rx(skb);
+ stats->rx_packets++;
+ stats->rx_bytes += length;
+
+ return;
+
+ drop:
+ if (skb)
+ dev_kfree_skb_irq(skb);
+ return;
+}
+
+static void __dldwd_ev_txexc(dldwd_priv_t *priv, hermes_t *hw)
+{
+ struct net_device *dev = &priv->ndev;
+ struct net_device_stats *stats = &priv->stats;
+
+ printk(KERN_WARNING "%s: Tx error!\n", dev->name);
+
+ netif_wake_queue(dev);
+ stats->tx_errors++;
+}
+
+static void __dldwd_ev_tx(dldwd_priv_t *priv, hermes_t *hw)
+{
+ struct net_device *dev = &priv->ndev;
+ struct net_device_stats *stats = &priv->stats;
+
+ DEBUG(3, "%s: Transmit completed\n", dev->name);
+
+ stats->tx_packets++;
+ netif_wake_queue(dev);
+}
+
+static void __dldwd_ev_alloc(dldwd_priv_t *priv, hermes_t *hw)
+{
+ uint16_t allocfid;
+
+ allocfid = hermes_read_regn(hw, ALLOCFID);
+ DEBUG(3, "%s: Allocation complete FID=0x%04x\n", priv->ndev.name, allocfid);
+
+ /* For some reason we don't seem to get transmit completed events properly */
+ if (allocfid == priv->txfid)
+ __dldwd_ev_tx(priv, hw);
+
+/* hermes_write_regn(hw, ALLOCFID, 0); */
+}
+
+/*
+ * struct net_device methods
+ */
+
+int
+dldwd_init(struct net_device *dev)
+{
+ dldwd_priv_t *priv = dev->priv;
+ hermes_t *hw = &priv->hw;
+ int err = 0;
+ hermes_id_t nickbuf;
+ uint16_t reclen;
+ int len;
+ char *vendor_str;
+ uint32_t firmver;
+
+ TRACE_ENTER("dldwd");
+
+ dldwd_lock(priv);
+
+ err = hermes_reset(hw);
+ if (err != 0) {
+ printk(KERN_ERR "%s: failed to reset hardware\n", dev->name);
+ goto out;
+ }
+
+ /* Get the firmware version */
+ err = hermes_read_staidentity(hw, USER_BAP, &priv->firmware_info);
+ if (err) {
+ printk(KERN_WARNING "%s: Error %d reading firmware info. Wildly guessing capabilities...\n",
+ dev->name, err);
+ memset(&priv->firmware_info, 0, sizeof(priv->firmware_info));
+ }
+
+ firmver = ((uint32_t)priv->firmware_info.major << 16) | priv->firmware_info.minor;
+ DEBUG(2, "%s: firmver = 0x%X\n", dev->name, firmver);
+
+ /* Determine capabilities from the firmware version */
+
+ switch (priv->firmware_info.vendor) {
+ case 0x1:
+ /* Lucent Wavelan IEEE, Lucent Orinoco, Cabletron RoamAbout,
+ * ELSA, Melco, HP, IBM, Dell 1150 cards */
+ vendor_str = "Lucent";
+ /* Lucent MAC : 00:60:1D:* & 00:02:2D:* */
+
+ priv->firmware_type = FIRMWARE_TYPE_LUCENT;
+ priv->broken_reset = 0;
+ priv->broken_allocate = 0;
+ priv->has_port3 = 1; /* Still works in 7.28 */
+ priv->has_ibss = (firmver >= 0x60006);
+ priv->has_ibss_any = (firmver >= 0x60010);
+ priv->has_wep = (firmver >= 0x40020);
+ priv->has_big_wep = 1; /* FIXME: this is wrong - how do we tell
+ Gold cards from the others? */
+ priv->has_mwo = (firmver >= 0x60000);
+ priv->has_pm = (firmver >= 0x40020);
+ priv->has_preamble = 0;
+ /* Tested with Lucent firmware :
+ * 1.16 ; 4.08 ; 4.52 ; 6.04 ; 6.16 ; 7.28 => Jean II
+ * Tested CableTron firmware : 4.32 => Anton */
+ break;
+ case 0x2:
+ vendor_str = "Generic Prism II";
+ /* Some D-Link cards report vendor 0x02... */
+
+ priv->firmware_type = FIRMWARE_TYPE_PRISM2;
+ priv->broken_reset = 0;
+ priv->broken_allocate = 0;
+ priv->has_port3 = 1;
+ priv->has_ibss = (firmver >= 0x00007); /* FIXME */
+ priv->has_wep = (firmver >= 0x00007); /* FIXME */
+ priv->has_big_wep = 0;
+ priv->has_mwo = 0;
+ priv->has_pm = (firmver >= 0x00007); /* FIXME */
+ priv->has_preamble = 0;
+
+ /* Tim Hurley -> D-Link card, vendor 02, firmware 0.08 */
+
+ /* Special case for Symbol cards */
+ if(firmver == 0x10001) {
+ /* Symbol , 3Com AirConnect, Intel, Ericsson WLAN */
+ vendor_str = "Symbol";
+ /* Intel MAC : 00:02:B3:* */
+ /* 3Com MAC : 00:50:DA:* */
+
+ /* FIXME : probably need to use SYMBOL_***ARY_VER
+ * to get proper firmware version */
+ priv->firmware_type = FIRMWARE_TYPE_SYMBOL;
+ priv->broken_reset = 0;
+ priv->broken_allocate = 1;
+ priv->has_port3 = 1;
+ priv->has_ibss = 1; /* FIXME */
+ priv->has_wep = 1; /* FIXME */
+ priv->has_big_wep = 1; /* RID_SYMBOL_KEY_LENGTH */
+ priv->has_mwo = 0;
+ priv->has_pm = 1; /* FIXME */
+ priv->has_preamble = 0; /* FIXME */
+ /* Tested with Intel firmware : v15 => Jean II */
+ }
+ break;
+ case 0x3:
+ vendor_str = "Samsung";
+ /* To check - Should cover Samsung & Compaq */
+
+ priv->firmware_type = FIRMWARE_TYPE_PRISM2;
+ priv->broken_reset = 0;
+ priv->broken_allocate = 0;
+ priv->has_port3 = 1;
+ priv->has_ibss = 0; /* FIXME: available in later firmwares */
+ priv->has_wep = (firmver >= 0x20000); /* FIXME */
+ priv->has_big_wep = 0; /* FIXME */
+ priv->has_mwo = 0;
+ priv->has_pm = (firmver >= 0x20000); /* FIXME */
+ priv->has_preamble = 0;
+ break;
+ case 0x6:
+ /* D-Link DWL 650, ... */
+ vendor_str = "LinkSys/D-Link";
+ /* D-Link MAC : 00:40:05:* */
+
+ priv->firmware_type = FIRMWARE_TYPE_PRISM2;
+ priv->broken_reset = 0;
+ priv->broken_allocate = 0;
+ priv->has_port3 = 1;
+ priv->has_ibss = (firmver >= 0x00007); /* FIXME */
+ priv->has_wep = (firmver >= 0x00007); /* FIXME */
+ priv->has_big_wep = 0;
+ priv->has_mwo = 0;
+ priv->has_pm = (firmver >= 0x00007); /* FIXME */
+ priv->has_preamble = 0;
+ /* Tested with D-Link firmware 0.07 => Jean II */
+ /* Note : with 0.07, IBSS to a Lucent card seem flaky */
+ break;
+ default:
+ vendor_str = "UNKNOWN";
+
+ priv->firmware_type = 0;
+ priv->broken_reset = 0;
+ priv->broken_allocate = 0;
+ priv->has_port3 = 0;
+ priv->has_ibss = 0;
+ priv->has_wep = 0;
+ priv->has_big_wep = 0;
+ priv->has_mwo = 0;
+ priv->has_pm = 0;
+ priv->has_preamble = 0;
+ }
+
+ printk(KERN_INFO "%s: Firmware ID %02X vendor 0x%x (%s) version %d.%02d\n",
+ dev->name, priv->firmware_info.id, priv->firmware_info.vendor,
+ vendor_str, priv->firmware_info.major, priv->firmware_info.minor);
+
+ if (priv->has_port3)
+ printk(KERN_INFO "%s: Ad-hoc demo mode supported.\n", dev->name);
+ if (priv->has_ibss)
+ printk(KERN_INFO "%s: IEEE standard IBSS ad-hoc mode supported.\n",
+ dev->name);
+ if (priv->has_wep) {
+ printk(KERN_INFO "%s: WEP supported, ", dev->name);
+ if (priv->has_big_wep)
+ printk("\"128\"-bit key.\n");
+ else
+ printk("40-bit key.\n");
+ }
+
+ /* Get the MAC address */
+ err = hermes_read_ltv(hw, USER_BAP, HERMES_RID_CNF_MACADDR,
+ ETH_ALEN, NULL, dev->dev_addr);
+ if (err) {
+ printk(KERN_WARNING "%s: failed to read MAC address!\n",
+ dev->name);
+ goto out;
+ }
+
+ printk(KERN_INFO "%s: MAC address %02X:%02X:%02X:%02X:%02X:%02X\n",
+ dev->name, dev->dev_addr[0], dev->dev_addr[1],
+ dev->dev_addr[2], dev->dev_addr[3], dev->dev_addr[4],
+ dev->dev_addr[5]);
+
+ /* Get the station name */
+ err = hermes_read_ltv(hw, USER_BAP, HERMES_RID_CNF_NICKNAME,
+ sizeof(nickbuf), &reclen, &nickbuf);
+ if (err) {
+ printk(KERN_ERR "%s: failed to read station name!n",
+ dev->name);
+ goto out;
+ }
+ if ( nickbuf.len )
+ len = MIN(IW_ESSID_MAX_SIZE, le16_to_cpu(nickbuf.len));
+ else
+ len = MIN(IW_ESSID_MAX_SIZE, 2 * reclen);
+ memcpy(priv->nick, &nickbuf.val, len);
+ priv->nick[len] = '\0';
+
+ printk(KERN_INFO "%s: Station name \"%s\"\n", dev->name, priv->nick);
+
+ /* Get allowed channels */
+ err = hermes_read_wordrec(hw, USER_BAP, HERMES_RID_CHANNEL_LIST, &priv->channel_mask);
+ if (err) {
+ printk(KERN_ERR "%s: failed to read channel list!\n",
+ dev->name);
+ goto out;
+ }
+
+ /* Get initial AP density */
+ err = hermes_read_wordrec(hw, USER_BAP, HERMES_RID_CNF_SYSTEM_SCALE, &priv->ap_density);
+ if (err) {
+ printk(KERN_ERR "%s: failed to read AP density!\n", dev->name);
+ goto out;
+ }
+
+ /* Get initial RTS threshold */
+ err = hermes_read_wordrec(hw, USER_BAP, HERMES_RID_CNF_RTS_THRESH, &priv->rts_thresh);
+ if (err) {
+ printk(KERN_ERR "%s: failed to read RTS threshold!\n", dev->name);
+ goto out;
+ }
+
+ /* Get initial fragmentation settings */
+ if (priv->has_mwo)
+ err = hermes_read_wordrec(hw, USER_BAP, HERMES_RID_CNF_MWO_ROBUST,
+ &priv->mwo_robust);
+ else
+ err = hermes_read_wordrec(hw, USER_BAP, HERMES_RID_CNF_FRAG_THRESH,
+ &priv->frag_thresh);
+ if (err) {
+ printk(KERN_ERR "%s: failed to read fragmentation settings!\n", dev->name);
+ goto out;
+ }
+
+ /* Set initial bitrate control*/
+ priv->tx_rate_ctrl = 3;
+
+ /* Power management setup */
+ if (priv->has_pm) {
+ priv->pm_on = 0;
+ priv->pm_mcast = 1;
+ err = hermes_read_wordrec(hw, USER_BAP, HERMES_RID_CNF_PM_PERIOD,
+ &priv->pm_period);
+ if (err) {
+ printk(KERN_ERR "%s: failed to read power management period!\n",
+ dev->name);
+ goto out;
+ }
+ err = hermes_read_wordrec(hw, USER_BAP, HERMES_RID_CNF_PM_HOLDOVER,
+ &priv->pm_timeout);
+ if (err) {
+ printk(KERN_ERR "%s: failed to read power management timeout!\n",
+ dev->name);
+ goto out;
+ }
+ }
+
+ /* Preamble setup */
+ if (priv->has_preamble) {
+ err = hermes_read_wordrec(hw, USER_BAP, HERMES_RID_CNF_SYMBOL_PREAMBLE, &priv->preamble);
+ if (err)
+ goto out;
+ }
+
+ /* Set up the default configuration */
+ priv->iw_mode = IW_MODE_INFRA;
+ /* By default use IEEE/IBSS ad-hoc mode if we have it */
+ priv->prefer_port3 = priv->has_port3 && (! priv->has_ibss);
+ set_port_type(priv);
+
+ priv->promiscuous = 0;
+ priv->allmulti = 0;
+ priv->wep_on = 0;
+ priv->tx_key = 0;
+
+ printk(KERN_INFO "%s: ready\n", dev->name);
+
+ out:
+ dldwd_unlock(priv);
+
+ TRACE_EXIT("dldwd");
+
+ return err;
+}
+
+struct net_device_stats *
+dldwd_get_stats(struct net_device *dev)
+{
+ dldwd_priv_t *priv = (dldwd_priv_t *)dev->priv;
+
+ return &priv->stats;
+}
+
+struct iw_statistics *
+dldwd_get_wireless_stats(struct net_device *dev)
+{
+ dldwd_priv_t *priv = (dldwd_priv_t *)dev->priv;
+ hermes_t *hw = &priv->hw;
+ struct iw_statistics *wstats = &priv->wstats;
+ int err = 0;
+ hermes_commsqual_t cq;
+
+ if (!priv->hw_ready)
+ return NULL;
+
+ dldwd_lock(priv);
+
+ if (priv->port_type == 3) {
+ memset(&wstats->qual, 0, sizeof(wstats->qual));
+#ifdef WIRELESS_SPY
+ /* If a spy address is defined, we report stats of the
+ * first spy address - Jean II */
+ if (priv->spy_number > 0) {
+ wstats->qual.qual = priv->spy_stat[0].qual;
+ wstats->qual.level = priv->spy_stat[0].level;
+ wstats->qual.noise = priv->spy_stat[0].noise;
+ wstats->qual.updated = priv->spy_stat[0].updated;
+ }
+#endif /* WIRELESS_SPY */
+ } else {
+ err = hermes_read_commsqual(hw, USER_BAP, &cq);
+
+ DEBUG(3, "%s: Global stats = %X-%X-%X\n", dev->name,
+ cq.qual, cq.signal, cq.noise);
+
+ /* Why are we using MIN/MAX ? We don't really care
+ * if the value goes above max, because we export the
+ * raw dBm values anyway. The normalisation should be done
+ * in user space - Jean II */
+ wstats->qual.qual = MAX(MIN(cq.qual, 0x8b-0x2f), 0);
+ wstats->qual.level = MAX(MIN(cq.signal, 0x8a), 0x2f) - 0x95;
+ wstats->qual.noise = MAX(MIN(cq.noise, 0x8a), 0x2f) - 0x95;
+ wstats->qual.updated = 7;
+ }
+
+ dldwd_unlock(priv);
+
+ if (err)
+ return NULL;
+
+ return wstats;
+}
+
+#ifdef WIRELESS_SPY
+static inline void dldwd_spy_gather(struct net_device *dev,
+ u_char *mac,
+ hermes_commsqual_t *cq)
+{
+ dldwd_priv_t *priv = (dldwd_priv_t *)dev->priv;
+ int i;
+
+ /* Gather wireless spy statistics: for each packet, compare the
+ * source address with out list, and if match, get the stats... */
+ for (i = 0; i < priv->spy_number; i++)
+ if (!memcmp(mac, priv->spy_address[i], ETH_ALEN)) {
+ priv->spy_stat[i].qual = MAX(MIN(cq->qual, 0x8b-0x2f), 0);
+ priv->spy_stat[i].level = MAX(MIN(cq->signal, 0x8a), 0x2f) - 0x95;
+ priv->spy_stat[i].noise = MAX(MIN(cq->noise, 0x8a), 0x2f) - 0x95;
+ priv->spy_stat[i].updated = 7;
+ }
+}
+#endif /* WIRELESS_SPY */
+
+void
+dldwd_stat_gather( struct net_device *dev,
+ struct sk_buff *skb,
+ struct dldwd_frame_hdr *hdr)
+{
+ dldwd_priv_t *priv = (dldwd_priv_t *)dev->priv;
+ hermes_commsqual_t cq;
+
+ /* Using spy support with lots of Rx packets, like in an
+ * infrastructure (AP), will really slow down everything, because
+ * the MAC address must be compared to each entry of the spy list.
+ * If the user really asks for it (set some address in the
+ * spy list), we do it, but he will pay the price.
+ * Note that to get here, you need both WIRELESS_SPY
+ * compiled in AND some addresses in the list !!!
+ */
+#ifdef WIRELESS_EXT
+ /* Note : gcc will optimise the whole section away if
+ * WIRELESS_SPY is not defined... - Jean II */
+ if (
+#ifdef WIRELESS_SPY
+ (priv->spy_number > 0) ||
+#endif
+ 0 )
+ {
+ u_char *stats = (u_char *) &(hdr->desc.q_info);
+ /* This code may look strange. Everywhere we are using 16 bit
+ * ints except here. I've verified that these are are the
+ * correct values. Please check on PPC - Jean II */
+ cq.signal = stats[1]; /* High order byte */
+ cq.noise = stats[0]; /* Low order byte */
+ cq.qual = stats[0] - stats[1]; /* Better than nothing */
+
+ DEBUG(3, "%s: Packet stats = %X-%X-%X\n", dev->name,
+ cq.qual, cq.signal, cq.noise);
+
+#ifdef WIRELESS_SPY
+ dldwd_spy_gather(dev, skb->mac.raw + ETH_ALEN, &cq);
+#endif
+ }
+#endif /* WIRELESS_EXT */
+}
+
+int
+dldwd_xmit(struct sk_buff *skb, struct net_device *dev)
+{
+ dldwd_priv_t *priv = (dldwd_priv_t *)dev->priv;
+ struct net_device_stats *stats = &priv->stats;
+ hermes_t *hw = &priv->hw;
+ int err = 0;
+ uint16_t txfid = priv->txfid;
+ char *p;
+ struct ethhdr *eh;
+ int len, data_len, data_off;
+ struct dldwd_frame_hdr hdr;
+ hermes_response_t resp;
+
+ if (! netif_running(dev)) {
+ printk(KERN_ERR "%s: Tx on stopped device!\n",
+ dev->name);
+ return 1;
+
+ }
+
+ if (netif_queue_stopped(dev)) {
+ printk(KERN_ERR "%s: Tx while transmitter busy!\n",
+ dev->name);
+ return 1;
+ }
+
+ dldwd_lock(priv);
+
+ /* Length of the packet body */
+ len = MAX(skb->len - ETH_HLEN, ETH_ZLEN);
+
+ eh = (struct ethhdr *)skb->data;
+
+ /* Build the IEEE 802.11 header */
+ memset(&hdr, 0, sizeof(hdr));
+ memcpy(hdr.p80211.addr1, eh->h_dest, ETH_ALEN);
+ memcpy(hdr.p80211.addr2, eh->h_source, ETH_ALEN);
+ hdr.p80211.frame_ctl = DLDWD_FTYPE_DATA;
+
+ /* Encapsulate Ethernet-II frames */
+ if (ntohs(eh->h_proto) > 1500) { /* Ethernet-II frame */
+ data_len = len;
+ data_off = sizeof(hdr);
+ p = skb->data + ETH_HLEN;
+
+ /* 802.11 header */
+ hdr.p80211.data_len = cpu_to_le16(data_len + ENCAPS_OVERHEAD);
+
+ /* 802.3 header */
+ memcpy(hdr.p8023.h_dest, eh->h_dest, ETH_ALEN);
+ memcpy(hdr.p8023.h_source, eh->h_source, ETH_ALEN);
+ hdr.p8023.h_proto = htons(data_len + ENCAPS_OVERHEAD);
+
+ /* 802.2 header */
+ memcpy(&hdr.p8022, &encaps_hdr, sizeof(encaps_hdr));
+
+ hdr.ethertype = eh->h_proto;
+ err = hermes_bap_pwrite(hw, USER_BAP, &hdr, sizeof(hdr),
+ txfid, 0);
+ if (err) {
+ printk(KERN_ERR
+ "%s: Error %d writing packet header to BAP\n",
+ dev->name, err);
+ stats->tx_errors++;
+ goto fail;
+ }
+ } else { /* IEEE 802.3 frame */
+ data_len = len + ETH_HLEN;
+ data_off = P8023_OFFSET;
+ p = skb->data;
+
+ /* 802.11 header */
+ hdr.p80211.data_len = cpu_to_le16(len);
+ err = hermes_bap_pwrite(hw, USER_BAP, &hdr, P8023_OFFSET,
+ txfid, 0);
+ if (err) {
+ printk(KERN_ERR
+ "%s: Error %d writing packet header to BAP\n",
+ dev->name, err);
+ stats->tx_errors++;
+ goto fail;
+ }
+ }
+
+ /* Round up for odd length packets */
+ err = hermes_bap_pwrite(hw, USER_BAP, p, RUP_EVEN(data_len), txfid, data_off);
+ if (err) {
+ printk(KERN_ERR "%s: Error %d writing packet data to BAP\n",
+ dev->name, err);
+ stats->tx_errors++;
+ goto fail;
+ }
+
+
+ /* Finally, we actually initiate the send */
+ err = hermes_docmd_wait(hw, HERMES_CMD_TX | HERMES_CMD_RECL, txfid, &resp);
+ if (err) {
+ printk(KERN_ERR "%s: Error %d transmitting packet\n", dev->name, err);
+ stats->tx_errors++;
+ goto fail;
+ }
+
+ dev->trans_start = jiffies;
+ stats->tx_bytes += data_off + data_len;
+
+ netif_stop_queue(dev);
+
+ dldwd_unlock(priv);
+
+ dev_kfree_skb(skb);
+
+ return 0;
+ fail:
+
+ dldwd_unlock(priv);
+ return err;
+}
+
+void
+dldwd_tx_timeout(struct net_device *dev)
+{
+ dldwd_priv_t *priv = (dldwd_priv_t *)dev->priv;
+ struct net_device_stats *stats = &priv->stats;
+ int err = 0;
+
+ printk(KERN_WARNING "%s: Tx timeout! Resetting card.\n", dev->name);
+
+ stats->tx_errors++;
+
+ err = dldwd_reset(priv);
+ if (err)
+ printk(KERN_ERR "%s: Error %d resetting card on Tx timeout!\n",
+ dev->name, err);
+ else {
+ dev->trans_start = jiffies;
+ netif_wake_queue(dev);
+ }
+}
+
+static int dldwd_ioctl_getiwrange(struct net_device *dev, struct iw_point *rrq)
+{
+ dldwd_priv_t *priv = dev->priv;
+ int err = 0;
+ int ptype;
+ struct iw_range range;
+ int numrates;
+ int i, k;
+
+ TRACE_ENTER(dev->name);
+
+ err = verify_area(VERIFY_WRITE, rrq->pointer, sizeof(range));
+ if (err)
+ return err;
+
+ rrq->length = sizeof(range);
+
+ dldwd_lock(priv);
+ ptype = priv->port_type;
+ dldwd_unlock(priv);
+
+ memset(&range, 0, sizeof(range));
+
+ /* Much of this shamelessly taken from wvlan_cs.c. No idea
+ * what it all means -dgibson */
+#if WIRELESS_EXT > 10
+ range.we_version_compiled = WIRELESS_EXT;
+ range.we_version_source = 11;
+#endif /* WIRELESS_EXT > 10 */
+
+ range.min_nwid = range.max_nwid = 0; /* We don't use nwids */
+
+ /* Set available channels/frequencies */
+ range.num_channels = NUM_CHANNELS;
+ k = 0;
+ for (i = 0; i < NUM_CHANNELS; i++) {
+ if (priv->channel_mask & (1 << i)) {
+ range.freq[k].i = i + 1;
+ range.freq[k].m = channel_frequency[i] * 100000;
+ range.freq[k].e = 1;
+ k++;
+ }
+
+ if (k >= IW_MAX_FREQUENCIES)
+ break;
+ }
+ range.num_frequency = k;
+
+ range.sensitivity = 3;
+
+ if ((ptype == 3) && (priv->spy_number == 0)){
+ /* Quality stats meaningless in ad-hoc mode */
+ range.max_qual.qual = 0;
+ range.max_qual.level = 0;
+ range.max_qual.noise = 0;
+ } else {
+ range.max_qual.qual = 0x8b - 0x2f;
+ range.max_qual.level = 0x2f - 0x95 - 1;
+ range.max_qual.noise = 0x2f - 0x95 - 1;
+ }
+
+ err = dldwd_hw_get_bitratelist(priv, &numrates,
+ range.bitrate, IW_MAX_BITRATES);
+ if (err)
+ return err;
+ range.num_bitrates = numrates;
+
+ /* Set an indication of the max TCP throughput in bit/s that we can
+ * expect using this interface. May be use for QoS stuff...
+ * Jean II */
+ if(numrates > 2)
+ range.throughput = 5 * 1000 * 1000; /* ~5 Mb/s */
+ else
+ range.throughput = 1.5 * 1000 * 1000; /* ~1.5 Mb/s */
+
+ range.min_rts = 0;
+ range.max_rts = 2347;
+ range.min_frag = 256;
+ range.max_frag = 2346;
+
+ dldwd_lock(priv);
+ if (priv->has_wep) {
+ range.max_encoding_tokens = MAX_KEYS;
+
+ range.encoding_size[0] = SMALL_KEY_SIZE;
+ range.num_encoding_sizes = 1;
+
+ if (priv->has_big_wep) {
+ range.encoding_size[1] = LARGE_KEY_SIZE;
+ range.num_encoding_sizes = 2;
+ }
+ } else {
+ range.num_encoding_sizes = 0;
+ range.max_encoding_tokens = 0;
+ }
+ dldwd_unlock(priv);
+
+ range.min_pmp = 0;
+ range.max_pmp = 65535000;
+ range.min_pmt = 0;
+ range.max_pmt = 65535 * 1000; /* ??? */
+ range.pmp_flags = IW_POWER_PERIOD;
+ range.pmt_flags = IW_POWER_TIMEOUT;
+ range.pm_capa = IW_POWER_PERIOD | IW_POWER_TIMEOUT | IW_POWER_UNICAST_R;
+
+ range.num_txpower = 1;
+ range.txpower[0] = 15; /* 15dBm */
+ range.txpower_capa = IW_TXPOW_DBM;
+
+#if WIRELESS_EXT > 10
+ range.retry_capa = IW_RETRY_LIMIT | IW_RETRY_LIFETIME;
+ range.retry_flags = IW_RETRY_LIMIT;
+ range.r_time_flags = IW_RETRY_LIFETIME;
+ range.min_retry = 0;
+ range.max_retry = 65535; /* ??? */
+ range.min_r_time = 0;
+ range.max_r_time = 65535 * 1000; /* ??? */
+#endif /* WIRELESS_EXT > 10 */
+
+ if (copy_to_user(rrq->pointer, &range, sizeof(range)))
+ return -EFAULT;
+
+ TRACE_EXIT(dev->name);
+
+ return 0;
+}
+
+static int dldwd_ioctl_setiwencode(struct net_device *dev, struct iw_point *erq)
+{
+ dldwd_priv_t *priv = dev->priv;
+ int index = (erq->flags & IW_ENCODE_INDEX) - 1;
+ int setindex = priv->tx_key;
+ int enable = priv->wep_on;
+ int restricted = priv->wep_restrict;
+ uint16_t xlen = 0;
+ int err = 0;
+ char keybuf[MAX_KEY_SIZE];
+
+ if (erq->pointer) {
+ /* We actually have a key to set */
+
+ if (copy_from_user(keybuf, erq->pointer, erq->length))
+ return -EFAULT;
+ }
+
+ dldwd_lock(priv);
+
+ if (erq->pointer) {
+ if (erq->length > MAX_KEY_SIZE) {
+ err = -E2BIG;
+ goto out;
+ }
+
+ if ( (erq->length > LARGE_KEY_SIZE)
+ || ( ! priv->has_big_wep && (erq->length > SMALL_KEY_SIZE)) ) {
+ err = -EINVAL;
+ goto out;
+ }
+
+ if ((index < 0) || (index >= MAX_KEYS))
+ index = priv->tx_key;
+
+ if (erq->length > SMALL_KEY_SIZE) {
+ xlen = LARGE_KEY_SIZE;
+ } else if (erq->length > 0) {
+ xlen = SMALL_KEY_SIZE;
+ } else
+ xlen = 0;
+
+ /* Switch on WEP if off */
+ if ((!enable) && (xlen > 0)) {
+ setindex = index;
+ enable = 1;
+ }
+ } else {
+ /* Important note : if the user do "iwconfig eth0 enc off",
+ * we will arrive there with an index of -1. This is valid
+ * but need to be taken care off... Jean II */
+ if ((index < 0) || (index >= MAX_KEYS)) {
+ if((index != -1) || (erq->flags == 0)) {
+ err = -EINVAL;
+ goto out;
+ }
+ } else {
+ /* Set the index : Check that the key is valid */
+ if(priv->keys[index].len == 0) {
+ err = -EINVAL;
+ goto out;
+ }
+ setindex = index;
+ }
+ }
+
+ if (erq->flags & IW_ENCODE_DISABLED)
+ enable = 0;
+ /* Only for Prism2 & Symbol cards (so far) - Jean II */
+ if (erq->flags & IW_ENCODE_OPEN)
+ restricted = 0;
+ if (erq->flags & IW_ENCODE_RESTRICTED)
+ restricted = 1;
+
+ if (erq->pointer) {
+ priv->keys[index].len = cpu_to_le16(xlen);
+ memset(priv->keys[index].data, 0, sizeof(priv->keys[index].data));
+ memcpy(priv->keys[index].data, keybuf, erq->length);
+ }
+ priv->tx_key = setindex;
+ priv->wep_on = enable;
+ priv->wep_restrict = restricted;
+
+ out:
+ dldwd_unlock(priv);
+
+ return 0;
+}
+
+static int dldwd_ioctl_getiwencode(struct net_device *dev, struct iw_point *erq)
+{
+ dldwd_priv_t *priv = dev->priv;
+ int index = (erq->flags & IW_ENCODE_INDEX) - 1;
+ uint16_t xlen = 0;
+ char keybuf[MAX_KEY_SIZE];
+
+
+ dldwd_lock(priv);
+
+ if ((index < 0) || (index >= MAX_KEYS))
+ index = priv->tx_key;
+
+ erq->flags = 0;
+ if (! priv->wep_on)
+ erq->flags |= IW_ENCODE_DISABLED;
+ erq->flags |= index + 1;
+
+ /* Only for symbol cards - Jean II */
+ if (priv->firmware_type != FIRMWARE_TYPE_LUCENT) {
+ if(priv->wep_restrict)
+ erq->flags |= IW_ENCODE_RESTRICTED;
+ else
+ erq->flags |= IW_ENCODE_OPEN;
+ }
+
+ xlen = le16_to_cpu(priv->keys[index].len);
+
+ erq->length = xlen;
+
+ if (erq->pointer) {
+ memcpy(keybuf, priv->keys[index].data, MAX_KEY_SIZE);
+ }
+
+ dldwd_unlock(priv);
+
+ if (erq->pointer) {
+ if (copy_to_user(erq->pointer, keybuf, xlen))
+ return -EFAULT;
+ }
+
+ return 0;
+}
+
+static int dldwd_ioctl_setessid(struct net_device *dev, struct iw_point *erq)
+{
+ dldwd_priv_t *priv = dev->priv;
+ char essidbuf[IW_ESSID_MAX_SIZE+1];
+
+ /* Note : ESSID is ignored in Ad-Hoc demo mode, but we can set it
+ * anyway... - Jean II */
+
+ memset(&essidbuf, 0, sizeof(essidbuf));
+
+ if (erq->flags) {
+ if (erq->length > IW_ESSID_MAX_SIZE)
+ return -E2BIG;
+
+ if (copy_from_user(&essidbuf, erq->pointer, erq->length))
+ return -EFAULT;
+
+ essidbuf[erq->length] = '\0';
+ }
+
+ dldwd_lock(priv);
+
+ memcpy(priv->desired_essid, essidbuf, IW_ESSID_MAX_SIZE+1);
+
+ dldwd_unlock(priv);
+
+ return 0;
+}
+
+static int dldwd_ioctl_getessid(struct net_device *dev, struct iw_point *erq)
+{
+ dldwd_priv_t *priv = dev->priv;
+ char essidbuf[IW_ESSID_MAX_SIZE+1];
+ int active;
+ int err = 0;
+
+ TRACE_ENTER(dev->name);
+
+ err = dldwd_hw_get_essid(priv, &active, essidbuf);
+ if (err)
+ return err;
+
+ erq->flags = 1;
+ erq->length = strlen(essidbuf) + 1;
+ if (erq->pointer)
+ if ( copy_to_user(erq->pointer, essidbuf, erq->length) )
+ return -EFAULT;
+
+ TRACE_EXIT(dev->name);
+
+ return 0;
+}
+
+static int dldwd_ioctl_setnick(struct net_device *dev, struct iw_point *nrq)
+{
+ dldwd_priv_t *priv = dev->priv;
+ char nickbuf[IW_ESSID_MAX_SIZE+1];
+
+ if (nrq->length > IW_ESSID_MAX_SIZE)
+ return -E2BIG;
+
+ memset(nickbuf, 0, sizeof(nickbuf));
+
+ if (copy_from_user(nickbuf, nrq->pointer, nrq->length))
+ return -EFAULT;
+
+ nickbuf[nrq->length] = '\0';
+
+ dldwd_lock(priv);
+
+ memcpy(priv->nick, nickbuf, sizeof(priv->nick));
+
+ dldwd_unlock(priv);
+
+ return 0;
+}
+
+static int dldwd_ioctl_getnick(struct net_device *dev, struct iw_point *nrq)
+{
+ dldwd_priv_t *priv = dev->priv;
+ char nickbuf[IW_ESSID_MAX_SIZE+1];
+
+ dldwd_lock(priv);
+ memcpy(nickbuf, priv->nick, IW_ESSID_MAX_SIZE+1);
+ dldwd_unlock(priv);
+
+ nrq->length = strlen(nickbuf)+1;
+
+ if (copy_to_user(nrq->pointer, nickbuf, sizeof(nickbuf)))
+ return -EFAULT;
+
+ return 0;
+}
+
+static int dldwd_ioctl_setfreq(struct net_device *dev, struct iw_freq *frq)
+{
+ dldwd_priv_t *priv = dev->priv;
+ int chan = -1;
+
+ /* We can only use this in Ad-Hoc demo mode to set the operating
+ * frequency, or in IBSS mode to set the frequency where the IBSS
+ * will be created - Jean II */
+ if (priv->iw_mode != IW_MODE_ADHOC)
+ return -EOPNOTSUPP;
+
+ if ( (frq->e == 0) && (frq->m <= 1000) ) {
+ /* Setting by channel number */
+ chan = frq->m;
+ } else {
+ /* Setting by frequency - search the table */
+ int mult = 1;
+ int i;
+
+ for (i = 0; i < (6 - frq->e); i++)
+ mult *= 10;
+
+ for (i = 0; i < NUM_CHANNELS; i++)
+ if (frq->m == (channel_frequency[i] * mult))
+ chan = i+1;
+ }
+
+ if ( (chan < 1) || (chan > NUM_CHANNELS) ||
+ ! (priv->channel_mask & (1 << (chan-1)) ) )
+ return -EINVAL;
+
+ dldwd_lock(priv);
+ priv->channel = chan;
+ dldwd_unlock(priv);
+
+ return 0;
+}
+
+static int dldwd_ioctl_getsens(struct net_device *dev, struct iw_param *srq)
+{
+ dldwd_priv_t *priv = dev->priv;
+ hermes_t *hw = &priv->hw;
+ uint16_t val;
+ int err;
+
+ dldwd_lock(priv);
+ err = hermes_read_wordrec(hw, USER_BAP, HERMES_RID_CNF_SYSTEM_SCALE, &val);
+ dldwd_unlock(priv);
+
+ if (err)
+ return err;
+
+ srq->value = val;
+ srq->fixed = 0; /* auto */
+
+ return 0;
+}
+
+static int dldwd_ioctl_setsens(struct net_device *dev, struct iw_param *srq)
+{
+ dldwd_priv_t *priv = dev->priv;
+ int val = srq->value;
+
+ if ((val < 1) || (val > 3))
+ return -EINVAL;
+
+ dldwd_lock(priv);
+ priv->ap_density = val;
+ dldwd_unlock(priv);
+
+ return 0;
+}
+
+static int dldwd_ioctl_setrts(struct net_device *dev, struct iw_param *rrq)
+{
+ dldwd_priv_t *priv = dev->priv;
+ int val = rrq->value;
+
+ if (rrq->disabled)
+ val = 2347;
+
+ if ( (val < 0) || (val > 2347) )
+ return -EINVAL;
+
+ dldwd_lock(priv);
+ priv->rts_thresh = val;
+ dldwd_unlock(priv);
+
+ return 0;
+}
+
+static int dldwd_ioctl_setfrag(struct net_device *dev, struct iw_param *frq)
+{
+ dldwd_priv_t *priv = dev->priv;
+ int err = 0;
+
+ dldwd_lock(priv);
+
+ if (priv->has_mwo) {
+ if (frq->disabled)
+ priv->mwo_robust = 0;
+ else {
+ if (frq->fixed)
+ printk(KERN_WARNING "%s: Fixed fragmentation not \
+supported on this firmware. Using MWO robust instead.\n", dev->name);
+ priv->mwo_robust = 1;
+ }
+ } else {
+ if (frq->disabled)
+ priv->frag_thresh = 2346;
+ else {
+ if ( (frq->value < 256) || (frq->value > 2346) )
+ err = -EINVAL;
+ else
+ priv->frag_thresh = frq->value & ~0x1; /* must be even */
+ }
+ }
+
+ dldwd_unlock(priv);
+
+ return err;
+}
+
+static int dldwd_ioctl_getfrag(struct net_device *dev, struct iw_param *frq)
+{
+ dldwd_priv_t *priv = dev->priv;
+ hermes_t *hw = &priv->hw;
+ int err = 0;
+ uint16_t val;
+
+ dldwd_lock(priv);
+
+ if (priv->has_mwo) {
+ err = hermes_read_wordrec(hw, USER_BAP, HERMES_RID_CNF_MWO_ROBUST, &val);
+ if (err)
+ val = 0;
+
+ frq->value = val ? 2347 : 0;
+ frq->disabled = ! val;
+ frq->fixed = 0;
+ } else {
+ err = hermes_read_wordrec(hw, USER_BAP, HERMES_RID_CNF_FRAG_THRESH, &val);
+ if (err)
+ val = 0;
+
+ frq->value = val;
+ frq->disabled = (val >= 2346);
+ frq->fixed = 1;
+ }
+
+ dldwd_unlock(priv);
+
+ return err;
+}
+
+static int dldwd_ioctl_setrate(struct net_device *dev, struct iw_param *rrq)
+{
+ dldwd_priv_t *priv = dev->priv;
+ int err = 0;
+ int rate_ctrl = -1;
+ int fixed, upto;
+ int brate;
+ int i;
+
+ dldwd_lock(priv);
+
+ /* Normalise value */
+ brate = rrq->value / 500000;
+
+ switch (priv->firmware_type) {
+ case FIRMWARE_TYPE_LUCENT: /* Lucent style rate */
+ if (! rrq->fixed) {
+ if (brate > 0)
+ brate = -brate;
+ else
+ brate = -22;
+ }
+
+ for (i = 0; i < NUM_RATES; i++)
+ if (rate_list[i] == brate) {
+ rate_ctrl = i;
+ break;
+ }
+
+ if ( (rate_ctrl < 1) || (rate_ctrl >= NUM_RATES) )
+ err = -EINVAL;
+ else
+ priv->tx_rate_ctrl = rate_ctrl;
+ break;
+ case FIRMWARE_TYPE_PRISM2: /* Prism II style rate */
+ case FIRMWARE_TYPE_SYMBOL: /* Symbol style rate */
+ switch(brate) {
+ case 0:
+ fixed = 0x0;
+ upto = 0x15;
+ break;
+ case 2:
+ fixed = 0x1;
+ upto = 0x1;
+ break;
+ case 4:
+ fixed = 0x2;
+ upto = 0x3;
+ break;
+ case 11:
+ fixed = 0x4;
+ upto = 0x7;
+ break;
+ case 22:
+ fixed = 0x8;
+ upto = 0x15;
+ break;
+ default:
+ fixed = 0x0;
+ upto = 0x0;
+ }
+ if (rrq->fixed)
+ rate_ctrl = fixed;
+ else
+ rate_ctrl = upto;
+ if (rate_ctrl == 0)
+ err = -EINVAL;
+ else
+ priv->tx_rate_ctrl = rate_ctrl;
+ break;
+ }
+
+ dldwd_unlock(priv);
+
+ return err;
+}
+
+static int dldwd_ioctl_getrate(struct net_device *dev, struct iw_param *rrq)
+{
+ dldwd_priv_t *priv = dev->priv;
+ hermes_t *hw = &priv->hw;
+ int err = 0;
+ uint16_t val;
+ int brate = 0;
+
+ dldwd_lock(priv);
+ err = hermes_read_wordrec(hw, USER_BAP, HERMES_RID_CNF_TX_RATE_CTRL, &val);
+ if (err)
+ goto out;
+
+ switch (priv->firmware_type) {
+ case FIRMWARE_TYPE_LUCENT: /* Lucent style rate */
+ brate = rate_list[val];
+
+ if (brate < 0) {
+ rrq->fixed = 0;
+
+ err = hermes_read_wordrec(hw, USER_BAP, HERMES_RID_CURRENT_TX_RATE, &val);
+ if (err)
+ goto out;
+
+ if (val == 6)
+ brate = 11;
+ else
+ brate = 2*val;
+ } else
+ rrq->fixed = 1;
+ break;
+ case FIRMWARE_TYPE_PRISM2: /* Prism II style rate */
+ case FIRMWARE_TYPE_SYMBOL: /* Symbol style rate */
+ /* Check if auto or fixed (crude approximation) */
+ if((val & 0x1) && (val > 1)) {
+ rrq->fixed = 0;
+
+ err = hermes_read_wordrec(hw, USER_BAP, HERMES_RID_CURRENT_TX_RATE, &val);
+ if (err)
+ goto out;
+ } else
+ rrq->fixed = 1;
+
+ if(val >= 8)
+ brate = 22;
+ else if(val >= 4)
+ brate = 11;
+ else if(val >= 2)
+ brate = 4;
+ else
+ brate = 2;
+ break;
+ }
+
+ rrq->value = brate * 500000;
+ rrq->disabled = 0;
+
+ out:
+ dldwd_unlock(priv);
+
+ return err;
+}
+
+static int dldwd_ioctl_setpower(struct net_device *dev, struct iw_param *prq)
+{
+ dldwd_priv_t *priv = dev->priv;
+ int err = 0;
+
+
+ dldwd_lock(priv);
+
+ if (prq->disabled) {
+ priv->pm_on = 0;
+ } else {
+ switch (prq->flags & IW_POWER_MODE) {
+ case IW_POWER_UNICAST_R:
+ priv->pm_mcast = 0;
+ priv->pm_on = 1;
+ break;
+ case IW_POWER_ALL_R:
+ priv->pm_mcast = 1;
+ priv->pm_on = 1;
+ break;
+ case IW_POWER_ON:
+ /* No flags : but we may have a value - Jean II */
+ break;
+ default:
+ err = -EINVAL;
+ }
+ if (err)
+ goto out;
+
+ if (prq->flags & IW_POWER_TIMEOUT) {
+ priv->pm_on = 1;
+ priv->pm_timeout = prq->value / 1000;
+ }
+ if (prq->flags & IW_POWER_PERIOD) {
+ priv->pm_on = 1;
+ priv->pm_period = prq->value / 1000;
+ }
+ /* It's valid to not have a value if we are just toggling
+ * the flags... Jean II */
+ if(!priv->pm_on) {
+ err = -EINVAL;
+ goto out;
+ }
+ }
+
+ out:
+ dldwd_unlock(priv);
+
+ return err;
+}
+
+static int dldwd_ioctl_getpower(struct net_device *dev, struct iw_param *prq)
+{
+ dldwd_priv_t *priv = dev->priv;
+ hermes_t *hw = &priv->hw;
+ int err = 0;
+ uint16_t enable, period, timeout, mcast;
+
+ dldwd_lock(priv);
+
+ err = hermes_read_wordrec(hw, USER_BAP, HERMES_RID_CNF_PM_ENABLE, &enable);
+ if (err)
+ goto out;
+
+ err = hermes_read_wordrec(hw, USER_BAP, HERMES_RID_CNF_PM_PERIOD, &period);
+ if (err)
+ goto out;
+
+ err = hermes_read_wordrec(hw, USER_BAP, HERMES_RID_CNF_PM_HOLDOVER, &timeout);
+ if (err)
+ goto out;
+
+ err = hermes_read_wordrec(hw, USER_BAP, HERMES_RID_CNF_PM_MCAST_RX, &mcast);
+ if (err)
+ goto out;
+
+ prq->disabled = !enable;
+ /* Note : by default, display the period */
+ if ((prq->flags & IW_POWER_TYPE) == IW_POWER_TIMEOUT) {
+ prq->flags = IW_POWER_TIMEOUT;
+ prq->value = timeout * 1000;
+ } else {
+ prq->flags = IW_POWER_PERIOD;
+ prq->value = period * 1000;
+ }
+ if (mcast)
+ prq->flags |= IW_POWER_ALL_R;
+ else
+ prq->flags |= IW_POWER_UNICAST_R;
+
+ out:
+ dldwd_unlock(priv);
+
+ return err;
+}
+
+#if WIRELESS_EXT > 10
+static int dldwd_ioctl_getretry(struct net_device *dev, struct iw_param *rrq)
+{
+ dldwd_priv_t *priv = dev->priv;
+ hermes_t *hw = &priv->hw;
+ int err = 0;
+ uint16_t short_limit, long_limit, lifetime;
+
+ dldwd_lock(priv);
+
+ err = hermes_read_wordrec(hw, USER_BAP, HERMES_RID_SHORT_RETRY_LIMIT, &short_limit);
+ if (err)
+ goto out;
+
+ err = hermes_read_wordrec(hw, USER_BAP, HERMES_RID_LONG_RETRY_LIMIT, &long_limit);
+ if (err)
+ goto out;
+
+ err = hermes_read_wordrec(hw, USER_BAP, HERMES_RID_MAX_TX_LIFETIME, &lifetime);
+ if (err)
+ goto out;
+
+ rrq->disabled = 0; /* Can't be disabled */
+
+ /* Note : by default, display the retry number */
+ if ((rrq->flags & IW_RETRY_TYPE) == IW_RETRY_LIFETIME) {
+ rrq->flags = IW_RETRY_LIFETIME;
+ rrq->value = lifetime * 1000; /* ??? */
+ } else {
+ /* By default, display the min number */
+ if ((rrq->flags & IW_RETRY_MAX)) {
+ rrq->flags = IW_RETRY_LIMIT | IW_RETRY_MAX;
+ rrq->value = long_limit;
+ } else {
+ rrq->flags = IW_RETRY_LIMIT;
+ rrq->value = short_limit;
+ if(short_limit != long_limit)
+ rrq->flags |= IW_RETRY_MIN;
+ }
+ }
+
+ out:
+ dldwd_unlock(priv);
+
+ return err;
+}
+#endif /* WIRELESS_EXT > 10 */
+
+static int dldwd_ioctl_setport3(struct net_device *dev, struct iwreq *wrq)
+{
+ dldwd_priv_t *priv = dev->priv;
+ int val = *( (int *) wrq->u.name );
+ int err = 0;
+
+ dldwd_lock(priv);
+ switch (val) {
+ case 0: /* Try to do IEEE ad-hoc mode */
+ if (! priv->has_ibss) {
+ err = -EINVAL;
+ break;
+ }
+ DEBUG(2, "%s: Prefer IBSS Ad-Hoc mode\n", dev->name);
+ priv->prefer_port3 = 0;
+
+ break;
+
+ case 1: /* Try to do Lucent proprietary ad-hoc mode */
+ if (! priv->has_port3) {
+ err = -EINVAL;
+ break;
+ }
+ DEBUG(2, "%s: Prefer Ad-Hoc demo mode\n", dev->name);
+ priv->prefer_port3 = 1;
+ break;
+
+ default:
+ err = -EINVAL;
+ }
+
+ if (! err)
+ /* Actually update the mode we are using */
+ set_port_type(priv);
+
+ dldwd_unlock(priv);
+
+ return err;
+}
+
+static int dldwd_ioctl_getport3(struct net_device *dev, struct iwreq *wrq)
+{
+ dldwd_priv_t *priv = dev->priv;
+ int *val = (int *)wrq->u.name;
+
+ dldwd_lock(priv);
+ *val = priv->prefer_port3;
+ dldwd_unlock(priv);
+
+ return 0;
+}
+
+/* Spy is used for link quality/strength measurements in Ad-Hoc mode
+ * Jean II */
+static int dldwd_ioctl_setspy(struct net_device *dev, struct iw_point *srq)
+{
+ dldwd_priv_t *priv = dev->priv;
+ struct sockaddr address[IW_MAX_SPY];
+ int number = srq->length;
+ int i;
+ int err = 0;
+
+ /* Check the number of addresses */
+ if (number > IW_MAX_SPY)
+ return -E2BIG;
+
+ /* Get the data in the driver */
+ if (srq->pointer) {
+ if (copy_from_user(address, srq->pointer,
+ sizeof(struct sockaddr) * number))
+ return -EFAULT;
+ }
+
+ /* Make sure nobody mess with the structure while we do */
+ dldwd_lock(priv);
+
+ /* dldwd_lock() doesn't disable interrupts, so make sure the
+ * interrupt rx path don't get confused while we copy */
+ priv->spy_number = 0;
+
+ if (number > 0) {
+ /* Extract the addresses */
+ for (i = 0; i < number; i++)
+ memcpy(priv->spy_address[i], address[i].sa_data,
+ ETH_ALEN);
+ /* Reset stats */
+ memset(priv->spy_stat, 0,
+ sizeof(struct iw_quality) * IW_MAX_SPY);
+ /* Set number of addresses */
+ priv->spy_number = number;
+ }
+
+ /* Time to show what we have done... */
+ DEBUG(0, "%s: New spy list:\n", dev->name);
+ for (i = 0; i < number; i++) {
+ DEBUG(0, "%s: %d - %02x:%02x:%02x:%02x:%02x:%02x\n",
+ dev->name, i+1,
+ priv->spy_address[i][0], priv->spy_address[i][1],
+ priv->spy_address[i][2], priv->spy_address[i][3],
+ priv->spy_address[i][4], priv->spy_address[i][5]);
+ }
+
+ /* Now, let the others play */
+ dldwd_unlock(priv);
+
+ return err;
+}
+
+static int dldwd_ioctl_getspy(struct net_device *dev, struct iw_point *srq)
+{
+ dldwd_priv_t *priv = dev->priv;
+ struct sockaddr address[IW_MAX_SPY];
+ struct iw_quality spy_stat[IW_MAX_SPY];
+ int number;
+ int i;
+
+ dldwd_lock(priv);
+
+ number = priv->spy_number;
+ if ((number > 0) && (srq->pointer)) {
+ /* Create address struct */
+ for (i = 0; i < number; i++) {
+ memcpy(address[i].sa_data, priv->spy_address[i],
+ ETH_ALEN);
+ address[i].sa_family = AF_UNIX;
+ }
+ /* Copy stats */
+ /* In theory, we should disable irqs while copying the stats
+ * because the rx path migh update it in the middle...
+ * Bah, who care ? - Jean II */
+ memcpy(&spy_stat, priv->spy_stat,
+ sizeof(struct iw_quality) * IW_MAX_SPY);
+ for (i=0; i < number; i++)
+ priv->spy_stat[i].updated = 0;
+ }
+
+ dldwd_unlock(priv);
+
+ /* Push stuff to user space */
+ srq->length = number;
+ if(copy_to_user(srq->pointer, address,
+ sizeof(struct sockaddr) * number))
+ return -EFAULT;
+ if(copy_to_user(srq->pointer + (sizeof(struct sockaddr)*number),
+ &spy_stat, sizeof(struct iw_quality) * number))
+ return -EFAULT;
+
+ return 0;
+}
+
+int
+dldwd_ioctl(struct net_device *dev, struct ifreq *rq, int cmd)
+{
+ dldwd_priv_t *priv = dev->priv;
+ struct iwreq *wrq = (struct iwreq *)rq;
+ int err = 0;
+ int changed = 0;
+
+ TRACE_ENTER(dev->name);
+
+ /* In theory, we could allow most of the the SET stuff to be done
+ * In practice, the laps of time at startup when the card is not
+ * ready is very short, so why bother...
+ * Note that hw_ready is different from up/down (ifconfig), when
+ * the device is not yet up, it is usually already ready...
+ * Jean II */
+ if (!priv->hw_ready)
+ return -ENODEV;
+
+ switch (cmd) {
+ case SIOCGIWNAME:
+ DEBUG(1, "%s: SIOCGIWNAME\n", dev->name);
+ strcpy(wrq->u.name, "IEEE 802.11-DS");
+ break;
+
+ case SIOCGIWAP:
+ DEBUG(1, "%s: SIOCGIWAP\n", dev->name);
+ wrq->u.ap_addr.sa_family = ARPHRD_ETHER;
+ err = dldwd_hw_get_bssid(priv, wrq->u.ap_addr.sa_data);
+ break;
+
+ case SIOCGIWRANGE:
+ DEBUG(1, "%s: SIOCGIWRANGE\n", dev->name);
+ err = dldwd_ioctl_getiwrange(dev, &wrq->u.data);
+ break;
+
+ case SIOCSIWMODE:
+ DEBUG(1, "%s: SIOCSIWMODE\n", dev->name);
+ dldwd_lock(priv);
+ switch (wrq->u.mode) {
+ case IW_MODE_ADHOC:
+ if (! (priv->has_ibss || priv->has_port3) )
+ err = -EINVAL;
+ else {
+ priv->iw_mode = IW_MODE_ADHOC;
+ changed = 1;
+ }
+ break;
+
+ case IW_MODE_INFRA:
+ priv->iw_mode = IW_MODE_INFRA;
+ changed = 1;
+ break;
+
+ default:
+ err = -EINVAL;
+ break;
+ }
+ set_port_type(priv);
+ dldwd_unlock(priv);
+ break;
+
+ case SIOCGIWMODE:
+ DEBUG(1, "%s: SIOCGIWMODE\n", dev->name);
+ dldwd_lock(priv);
+ wrq->u.mode = priv->iw_mode;
+ dldwd_unlock(priv);
+ break;
+
+ case SIOCSIWENCODE:
+ DEBUG(1, "%s: SIOCSIWENCODE\n", dev->name);
+ if (! priv->has_wep) {
+ err = -EOPNOTSUPP;
+ break;
+ }
+
+ err = dldwd_ioctl_setiwencode(dev, &wrq->u.encoding);
+ if (! err)
+ changed = 1;
+ break;
+
+ case SIOCGIWENCODE:
+ DEBUG(1, "%s: SIOCGIWENCODE\n", dev->name);
+ if (! priv->has_wep) {
+ err = -EOPNOTSUPP;
+ break;
+ }
+
+ if (! capable(CAP_NET_ADMIN)) {
+ err = -EPERM;
+ break;
+ }
+
+ err = dldwd_ioctl_getiwencode(dev, &wrq->u.encoding);
+ break;
+
+ case SIOCSIWESSID:
+ DEBUG(1, "%s: SIOCSIWESSID\n", dev->name);
+ err = dldwd_ioctl_setessid(dev, &wrq->u.essid);
+ if (! err)
+ changed = 1;
+ break;
+
+ case SIOCGIWESSID:
+ DEBUG(1, "%s: SIOCGIWESSID\n", dev->name);
+ err = dldwd_ioctl_getessid(dev, &wrq->u.essid);
+ break;
+
+ case SIOCSIWNICKN:
+ DEBUG(1, "%s: SIOCSIWNICKN\n", dev->name);
+ err = dldwd_ioctl_setnick(dev, &wrq->u.data);
+ if (! err)
+ changed = 1;
+ break;
+
+ case SIOCGIWNICKN:
+ DEBUG(1, "%s: SIOCGIWNICKN\n", dev->name);
+ err = dldwd_ioctl_getnick(dev, &wrq->u.data);
+ break;
+
+ case SIOCGIWFREQ:
+ DEBUG(1, "%s: SIOCGIWFREQ\n", dev->name);
+ wrq->u.freq.m = dldwd_hw_get_freq(priv);
+ wrq->u.freq.e = 1;
+ break;
+
+ case SIOCSIWFREQ:
+ DEBUG(1, "%s: SIOCSIWFREQ\n", dev->name);
+ err = dldwd_ioctl_setfreq(dev, &wrq->u.freq);
+ if (! err)
+ changed = 1;
+ break;
+
+ case SIOCGIWSENS:
+ DEBUG(1, "%s: SIOCGIWSENS\n", dev->name);
+ err = dldwd_ioctl_getsens(dev, &wrq->u.sens);
+ break;
+
+ case SIOCSIWSENS:
+ DEBUG(1, "%s: SIOCSIWSENS\n", dev->name);
+ err = dldwd_ioctl_setsens(dev, &wrq->u.sens);
+ if (! err)
+ changed = 1;
+ break;
+
+ case SIOCGIWRTS:
+ DEBUG(1, "%s: SIOCGIWRTS\n", dev->name);
+ wrq->u.rts.value = priv->rts_thresh;
+ wrq->u.rts.disabled = (wrq->u.rts.value == 2347);
+ wrq->u.rts.fixed = 1;
+ break;
+
+ case SIOCSIWRTS:
+ DEBUG(1, "%s: SIOCSIWRTS\n", dev->name);
+ err = dldwd_ioctl_setrts(dev, &wrq->u.rts);
+ if (! err)
+ changed = 1;
+ break;
+
+ case SIOCSIWFRAG:
+ DEBUG(1, "%s: SIOCSIWFRAG\n", dev->name);
+ err = dldwd_ioctl_setfrag(dev, &wrq->u.frag);
+ if (! err)
+ changed = 1;
+ break;
+
+ case SIOCGIWFRAG:
+ DEBUG(1, "%s: SIOCGIWFRAG\n", dev->name);
+ err = dldwd_ioctl_getfrag(dev, &wrq->u.frag);
+ break;
+
+ case SIOCSIWRATE:
+ DEBUG(1, "%s: SIOCSIWRATE\n", dev->name);
+ err = dldwd_ioctl_setrate(dev, &wrq->u.bitrate);
+ if (! err)
+ changed = 1;
+ break;
+
+ case SIOCGIWRATE:
+ DEBUG(1, "%s: SIOCGIWRATE\n", dev->name);
+ err = dldwd_ioctl_getrate(dev, &wrq->u.bitrate);
+ break;
+
+ case SIOCSIWPOWER:
+ DEBUG(1, "%s: SIOCSIWPOWER\n", dev->name);
+ err = dldwd_ioctl_setpower(dev, &wrq->u.power);
+ if (! err)
+ changed = 1;
+ break;
+
+ case SIOCGIWPOWER:
+ DEBUG(1, "%s: SIOCGIWPOWER\n", dev->name);
+ err = dldwd_ioctl_getpower(dev, &wrq->u.power);
+ break;
+
+ case SIOCGIWTXPOW:
+ DEBUG(1, "%s: SIOCGIWTXPOW\n", dev->name);
+ /* The card only supports one tx power, so this is easy */
+ wrq->u.txpower.value = 15; /* dBm */
+ wrq->u.txpower.fixed = 1;
+ wrq->u.txpower.disabled = 0;
+ wrq->u.txpower.flags = IW_TXPOW_DBM;
+ break;
+
+#if WIRELESS_EXT > 10
+ case SIOCSIWRETRY:
+ DEBUG(1, "%s: SIOCSIWRETRY\n", dev->name);
+ err = -EOPNOTSUPP;
+ break;
+
+ case SIOCGIWRETRY:
+ DEBUG(1, "%s: SIOCGIWRETRY\n", dev->name);
+ err = dldwd_ioctl_getretry(dev, &wrq->u.retry);
+ break;
+#endif /* WIRELESS_EXT > 10 */
+
+ case SIOCSIWSPY:
+ DEBUG(1, "%s: SIOCSIWSPY\n", dev->name);
+
+ err = dldwd_ioctl_setspy(dev, &wrq->u.data);
+ break;
+
+ case SIOCGIWSPY:
+ DEBUG(1, "%s: SIOCGIWSPY\n", dev->name);
+
+ err = dldwd_ioctl_getspy(dev, &wrq->u.data);
+ break;
+
+ case SIOCGIWPRIV:
+ DEBUG(1, "%s: SIOCGIWPRIV\n", dev->name);
+ if (wrq->u.data.pointer) {
+ struct iw_priv_args privtab[] = {
+ { SIOCDEVPRIVATE + 0x0, 0, 0, "force_reset" },
+ { SIOCDEVPRIVATE + 0x2,
+ IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
+ 0, "set_port3" },
+ { SIOCDEVPRIVATE + 0x3, 0,
+ IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
+ "get_port3" },
+ { SIOCDEVPRIVATE + 0x4,
+ IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
+ 0, "set_preamble" },
+ { SIOCDEVPRIVATE + 0x5, 0,
+ IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
+ "get_preamble" }
+ };
+
+ err = verify_area(VERIFY_WRITE, wrq->u.data.pointer, sizeof(privtab));
+ if (err)
+ break;
+
+ wrq->u.data.length = sizeof(privtab) / sizeof(privtab[0]);
+ if (copy_to_user(wrq->u.data.pointer, privtab, sizeof(privtab)))
+ err = -EFAULT;
+ }
+ break;
+
+ case SIOCDEVPRIVATE + 0x0: /* force_reset */
+ DEBUG(1, "%s: SIOCDEVPRIVATE + 0x0 (force_reset)\n",
+ dev->name);
+ if (! capable(CAP_NET_ADMIN)) {
+ err = -EPERM;
+ break;
+ }
+
+ printk(KERN_DEBUG "%s: Forcing reset!\n", dev->name);
+ dldwd_reset(priv);
+ break;
+
+ case SIOCDEVPRIVATE + 0x2: /* set_port3 */
+ DEBUG(1, "%s: SIOCDEVPRIVATE + 0x2 (set_port3)\n",
+ dev->name);
+ if (! capable(CAP_NET_ADMIN)) {
+ err = -EPERM;
+ break;
+ }
+
+ err = dldwd_ioctl_setport3(dev, wrq);
+ if (! err)
+ changed = 1;
+ break;
+
+ case SIOCDEVPRIVATE + 0x3: /* get_port3 */
+ DEBUG(1, "%s: SIOCDEVPRIVATE + 0x3 (get_port3)\n",
+ dev->name);
+ err = dldwd_ioctl_getport3(dev, wrq);
+ break;
+
+ case SIOCDEVPRIVATE + 0x4: /* set_preamble */
+ DEBUG(1, "%s: SIOCDEVPRIVATE + 0x4 (set_preamble)\n",
+ dev->name);
+ if (! capable(CAP_NET_ADMIN)) {
+ err = -EPERM;
+ break;
+ }
+
+ /* 802.11b has recently defined some short preamble.
+ * Basically, the Phy header has been reduced in size.
+ * This increase performance, especially at high rates
+ * (the preamble is transmitted at 1Mb/s), unfortunately
+ * this give compatibility troubles... - Jean II */
+ if(priv->has_preamble) {
+ int val = *( (int *) wrq->u.name );
+
+ dldwd_lock(priv);
+ if(val)
+ priv->preamble = 1;
+ else
+ priv->preamble = 0;
+ dldwd_unlock(priv);
+ changed = 1;
+ } else
+ err = -EOPNOTSUPP;
+ break;
+
+ case SIOCDEVPRIVATE + 0x5: /* get_preamble */
+ DEBUG(1, "%s: SIOCDEVPRIVATE + 0x5 (get_preamble)\n",
+ dev->name);
+ if(priv->has_preamble) {
+ int *val = (int *)wrq->u.name;
+
+ dldwd_lock(priv);
+ *val = priv->preamble;
+ dldwd_unlock(priv);
+ } else
+ err = -EOPNOTSUPP;
+ break;
+
+ default:
+ err = -EOPNOTSUPP;
+ }
+
+ if (! err && changed && netif_running(dev)) {
+ err = dldwd_reset(priv);
+ if (err) {
+ /* Ouch ! What are we supposed to do ? */
+ printk(KERN_ERR "orinoco_cs: Failed to set parameters on %s\n",
+ dev->name);
+ netif_stop_queue(dev);
+ dldwd_shutdown(priv);
+ priv->hw_ready = 0;
+ }
+ }
+
+ TRACE_EXIT(dev->name);
+
+ return err;
+}
+
+int
+dldwd_change_mtu(struct net_device *dev, int new_mtu)
+{
+ TRACE_ENTER(dev->name);
+
+ if ( (new_mtu < DLDWD_MIN_MTU) || (new_mtu > DLDWD_MAX_MTU) )
+ return -EINVAL;
+
+ dev->mtu = new_mtu;
+
+ TRACE_EXIT(dev->name);
+
+ return 0;
+}
+
+static void
+__dldwd_set_multicast_list(struct net_device *dev)
+{
+ dldwd_priv_t *priv = dev->priv;
+ hermes_t *hw = &priv->hw;
+ int err = 0;
+ int promisc, allmulti, mc_count;
+
+ /* We'll wait until it's ready. Anyway, the network doesn't call us
+ * here until we are open - Jean II */
+ if (!priv->hw_ready)
+ return;
+
+
+ TRACE_ENTER(dev->name);
+
+ DEBUG(3, "dev->flags=0x%x, priv->promiscuous=%d, dev->mc_count=%d priv->mc_count=%d\n",
+ dev->flags, priv->promiscuous, dev->mc_count, priv->mc_count);
+
+ /* The Hermes doesn't seem to have an allmulti mode, so we go
+ * into promiscuous mode and let the upper levels deal. */
+ if ( (dev->flags & IFF_PROMISC) ) {
+ promisc = 1;
+ allmulti = 0;
+ mc_count = 0;
+ } else if ( (dev->flags & IFF_ALLMULTI) ||
+ (dev->mc_count > HERMES_MAX_MULTICAST) ) {
+ promisc = 0;
+ allmulti = 1;
+ mc_count = HERMES_MAX_MULTICAST;
+ } else {
+ promisc = 0;
+ allmulti = 0;
+ mc_count = dev->mc_count;
+ }
+
+ DEBUG(3, "promisc=%d mc_count=%d\n",
+ promisc, mc_count);
+
+ if (promisc != priv->promiscuous) { /* Don't touch the hardware if we don't have to */
+ err = hermes_write_wordrec(hw, USER_BAP, HERMES_RID_CNF_PROMISCUOUS,
+ promisc);
+ if (err) {
+ printk(KERN_ERR "%s: Error %d setting promiscuity to %d.\n",
+ dev->name, err, promisc);
+ } else
+ priv->promiscuous = promisc;
+ }
+
+ if (allmulti) {
+ /* FIXME: This method of doing allmulticast reception
+ comes from the NetBSD driver. Haven't actually
+ tested whether it works or not. */
+ hermes_multicast_t mclist;
+
+ memset(&mclist, 0, sizeof(mclist));
+ err = HERMES_WRITE_RECORD(hw, USER_BAP, HERMES_RID_CNF_MULTICAST_LIST, &mclist);
+ if (err)
+ printk(KERN_ERR "%s: Error %d setting multicast list.\n",
+ dev->name, err);
+ else
+ priv->allmulti = 1;
+
+ } else if (mc_count || (! mc_count && priv->mc_count) ) {
+ struct dev_mc_list *p = dev->mc_list;
+ hermes_multicast_t mclist;
+ int i;
+
+ for (i = 0; i < mc_count; i++) {
+ /* First some paranoid checks */
+ if (! p) {
+ printk(KERN_ERR "%s: Multicast list shorter than mc_count.\n",
+ dev->name);
+ break;
+ }
+ if (p->dmi_addrlen != ETH_ALEN) {
+
+ printk(KERN_ERR "%s: Bad address size (%d) in multicast list.\n",
+ dev->name, p->dmi_addrlen);
+ break;
+ }
+
+ memcpy(mclist.addr[i], p->dmi_addr, ETH_ALEN);
+ p = p->next;
+ }
+
+ /* More paranoia */
+ if (p)
+ printk(KERN_ERR "%s: Multicast list longer than mc_count.\n",
+ dev->name);
+
+ priv->mc_count = i;
+
+ DEBUG(3, "priv->mc_count = %d\n", priv->mc_count);
+
+ err = hermes_write_ltv(hw, USER_BAP, HERMES_RID_CNF_MULTICAST_LIST,
+ HERMES_BYTES_TO_RECLEN(priv->mc_count * ETH_ALEN),
+ &mclist);
+ if (err)
+ printk(KERN_ERR "%s: Error %d setting multicast list.\n",
+ dev->name, err);
+ else
+ priv->allmulti = 0;
+ }
+
+ /* Since we can set the promiscuous flag when it wasn't asked
+ for, make sure the net_device knows about it. */
+ if (priv->promiscuous)
+ dev->flags |= IFF_PROMISC;
+ else
+ dev->flags &= ~IFF_PROMISC;
+
+ if (priv->allmulti)
+ dev->flags |= IFF_ALLMULTI;
+ else
+ dev->flags &= ~IFF_ALLMULTI;
+
+ TRACE_EXIT(dev->name);
+}
+
+/*
+ * procfs stuff
+ */
+
+static struct proc_dir_entry *dir_base = NULL;
+
+/*
+ * This function updates the total amount of data printed so far. It then
+ * determines if the amount of data printed into a buffer has reached the
+ * offset requested. If it hasn't, then the buffer is shifted over so that
+ * the next bit of data can be printed over the old bit. If the total
+ * amount printed so far exceeds the total amount requested, then this
+ * function returns 1, otherwise 0.
+ */
+static int
+
+shift_buffer(char *buffer, int requested_offset, int requested_len,
+ int *total, int *slop, char **buf)
+{
+ int printed;
+
+ printed = *buf - buffer;
+ if (*total + printed <= requested_offset) {
+ *total += printed;
+ *buf = buffer;
+ }
+ else {
+ if (*total < requested_offset) {
+ *slop = requested_offset - *total;
+ }
+ *total = requested_offset + printed - *slop;
+ }
+ if (*total > requested_offset + requested_len) {
+ return 1;
+ }
+ else {
+ return 0;
+ }
+}
+
+/*
+ * This function calculates the actual start of the requested data
+ * in the buffer. It also calculates actual length of data returned,
+ * which could be less that the amount of data requested.
+ */
+#define PROC_BUFFER_SIZE 4096
+#define PROC_SAFE_SIZE 3072
+
+static int
+calc_start_len(char *buffer, char **start, int requested_offset,
+ int requested_len, int total, char *buf)
+{
+ int return_len, buffer_len;
+
+ buffer_len = buf - buffer;
+ if (buffer_len >= PROC_BUFFER_SIZE - 1) {
+ printk(KERN_ERR "calc_start_len: exceeded /proc buffer size\n");
+ }
+
+ /*
+ * There may be bytes before and after the
+ * chunk that was actually requested.
+ */
+ return_len = total - requested_offset;
+ if (return_len < 0) {
+ return_len = 0;
+ }
+ *start = buf - return_len;
+ if (return_len > requested_len) {
+ return_len = requested_len;
+ }
+ return return_len;
+}
+
+static int
+dldwd_proc_get_hermes_regs(char *page, char **start, off_t requested_offset,
+ int requested_len, int *eof, void *data)
+{
+ dldwd_priv_t *dev = (dldwd_priv_t *)data;
+ hermes_t *hw = &dev->hw;
+ char *buf;
+ int total = 0, slop = 0;
+
+ /* Hum, in this case hardware register are probably not readable... */
+ if (!dev->hw_ready)
+ return -ENODEV;
+
+ buf = page;
+
+#define DHERMESREG(name) buf += sprintf(buf, "%-16s: %04x\n", #name, hermes_read_regn(hw, name))
+
+ DHERMESREG(CMD);
+ DHERMESREG(PARAM0);
+ DHERMESREG(PARAM1);
+ DHERMESREG(PARAM2);
+ DHERMESREG(STATUS);
+ DHERMESREG(RESP0);
+ DHERMESREG(RESP1);
+ DHERMESREG(RESP2);
+ DHERMESREG(INFOFID);
+ DHERMESREG(RXFID);
+ DHERMESREG(ALLOCFID);
+ DHERMESREG(TXCOMPLFID);
+ DHERMESREG(SELECT0);
+ DHERMESREG(OFFSET0);
+ DHERMESREG(SELECT1);
+ DHERMESREG(OFFSET1);
+ DHERMESREG(EVSTAT);
+ DHERMESREG(INTEN);
+ DHERMESREG(EVACK);
+ DHERMESREG(CONTROL);
+ DHERMESREG(SWSUPPORT0);
+ DHERMESREG(SWSUPPORT1);
+ DHERMESREG(SWSUPPORT2);
+ DHERMESREG(AUXPAGE);
+ DHERMESREG(AUXOFFSET);
+ DHERMESREG(AUXDATA);
+#undef DHERMESREG
+
+ shift_buffer(page, requested_offset, requested_len, &total,
+ &slop, &buf);
+ return calc_start_len(page, start, requested_offset, requested_len,
+ total, buf);
+}
+
+struct {
+ uint16_t rid;
+ char *name;
+ int minlen, maxlen;
+ int displaytype;
+#define DISPLAY_WORDS 0
+#define DISPLAY_BYTES 1
+#define DISPLAY_STRING 2
+} record_table[] = {
+#define RTCNFENTRY(name, type) { HERMES_RID_CNF_##name, #name, 0, LTV_BUF_SIZE, type }
+ RTCNFENTRY(PORTTYPE, DISPLAY_WORDS),
+ RTCNFENTRY(MACADDR, DISPLAY_BYTES),
+ RTCNFENTRY(DESIRED_SSID, DISPLAY_STRING),
+ RTCNFENTRY(CHANNEL, DISPLAY_WORDS),
+ RTCNFENTRY(OWN_SSID, DISPLAY_STRING),
+ RTCNFENTRY(SYSTEM_SCALE, DISPLAY_WORDS),
+ RTCNFENTRY(MAX_DATA_LEN, DISPLAY_WORDS),
+ RTCNFENTRY(PM_ENABLE, DISPLAY_WORDS),
+ RTCNFENTRY(PM_MCAST_RX, DISPLAY_WORDS),
+ RTCNFENTRY(PM_PERIOD, DISPLAY_WORDS),
+ RTCNFENTRY(NICKNAME, DISPLAY_STRING),
+ RTCNFENTRY(WEP_ON, DISPLAY_WORDS),
+ RTCNFENTRY(MWO_ROBUST, DISPLAY_WORDS),
+ RTCNFENTRY(MULTICAST_LIST, DISPLAY_BYTES),
+ RTCNFENTRY(CREATEIBSS, DISPLAY_WORDS),
+ RTCNFENTRY(FRAG_THRESH, DISPLAY_WORDS),
+ RTCNFENTRY(RTS_THRESH, DISPLAY_WORDS),
+ RTCNFENTRY(TX_RATE_CTRL, DISPLAY_WORDS),
+ RTCNFENTRY(PROMISCUOUS, DISPLAY_WORDS),
+ RTCNFENTRY(KEYS, DISPLAY_BYTES),
+ RTCNFENTRY(TX_KEY, DISPLAY_WORDS),
+ RTCNFENTRY(TICKTIME, DISPLAY_WORDS),
+ RTCNFENTRY(PRISM2_TX_KEY, DISPLAY_WORDS),
+ RTCNFENTRY(PRISM2_KEY0, DISPLAY_BYTES),
+ RTCNFENTRY(PRISM2_KEY1, DISPLAY_BYTES),
+ RTCNFENTRY(PRISM2_KEY2, DISPLAY_BYTES),
+ RTCNFENTRY(PRISM2_KEY3, DISPLAY_BYTES),
+ RTCNFENTRY(PRISM2_WEP_ON, DISPLAY_WORDS),
+#undef RTCNFENTRY
+#define RTINFENTRY(name,type) { HERMES_RID_##name, #name, 0, LTV_BUF_SIZE, type }
+ RTINFENTRY(CHANNEL_LIST, DISPLAY_WORDS),
+ RTINFENTRY(STAIDENTITY, DISPLAY_WORDS),
+ RTINFENTRY(CURRENT_SSID, DISPLAY_STRING),
+ RTINFENTRY(CURRENT_BSSID, DISPLAY_BYTES),
+ RTINFENTRY(COMMSQUALITY, DISPLAY_WORDS),
+ RTINFENTRY(CURRENT_TX_RATE, DISPLAY_WORDS),
+ RTINFENTRY(WEP_AVAIL, DISPLAY_WORDS),
+ RTINFENTRY(CURRENT_CHANNEL, DISPLAY_WORDS),
+ RTINFENTRY(DATARATES, DISPLAY_BYTES),
+#undef RTINFENTRY
+};
+#define NUM_RIDS ( sizeof(record_table) / sizeof(record_table[0]) )
+
+static int
+dldwd_proc_get_hermes_recs(char *page, char **start, off_t requested_offset,
+ int requested_len, int *eof, void *data)
+{
+ dldwd_priv_t *dev = (dldwd_priv_t *)data;
+ hermes_t *hw = &dev->hw;
+ char *buf;
+ int total = 0, slop = 0;
+ int i;
+ uint16_t length;
+ int err;
+
+ /* Hum, in this case hardware register are probably not readable... */
+ if (!dev->hw_ready)
+ return -ENODEV;
+
+ buf = page;
+
+ /* print out all the config RIDs */
+ for (i = 0; i < NUM_RIDS; i++) {
+ uint16_t rid = record_table[i].rid;
+ int minlen = record_table[i].minlen;
+ int maxlen = record_table[i].maxlen;
+ int len;
+ uint8_t *val8;
+ uint16_t *val16;
+ int j;
+
+ val8 = kmalloc(maxlen + 2, GFP_KERNEL);
+ if (! val8)
+ return -ENOMEM;
+
+ err = hermes_read_ltv(hw, USER_BAP, rid, maxlen,
+ &length, val8);
+ if (err) {
+ DEBUG(0, "Error %d reading RID 0x%04x\n", err, rid);
+ continue;
+ }
+ val16 = (uint16_t *)val8;
+
+ buf += sprintf(buf, "%-15s (0x%04x): length=%d (%d bytes)\tvalue=", record_table[i].name,
+ rid, length, (length-1)*2);
+ len = MIN( MAX(minlen, (length-1)*2), maxlen);
+
+ switch (record_table[i].displaytype) {
+ case DISPLAY_WORDS:
+ for (j = 0; j < len / 2; j++) {
+ buf += sprintf(buf, "%04X-", le16_to_cpu(val16[j]));
+ }
+ buf--;
+ break;
+
+ case DISPLAY_BYTES:
+ default:
+ for (j = 0; j < len; j++) {
+ buf += sprintf(buf, "%02X:", val8[j]);
+ }
+ buf--;
+ break;
+
+ case DISPLAY_STRING:
+ len = MIN(len, le16_to_cpu(val16[0])+2);
+ val8[len] = '\0';
+ buf += sprintf(buf, "\"%s\"", (char *)&val16[1]);
+ break;
+ }
+
+ buf += sprintf(buf, "\n");
+
+ kfree(val8);
+
+ if (shift_buffer(page, requested_offset, requested_len,
+ &total, &slop, &buf))
+ break;
+
+ if ( (buf - page) > PROC_SAFE_SIZE )
+ break;
+ }
+
+ return calc_start_len(page, start, requested_offset, requested_len,
+ total, buf);
+}
+
+/* initialise the /proc subsystem for the hermes driver, creating the
+ * separate entries */
+static int
+dldwd_proc_init(void)
+{
+ int err = 0;
+
+ TRACE_ENTER("dldwd");
+
+ /* create the directory for it to sit in */
+ dir_base = create_proc_entry("hermes", S_IFDIR, &proc_root);
+ if (dir_base == NULL) {
+ printk(KERN_ERR "Unable to initialise /proc/hermes.\n");
+ dldwd_proc_cleanup();
+ err = -ENOMEM;
+ }
+
+ TRACE_EXIT("dldwd");
+
+ return err;
+}
+
+int
+dldwd_proc_dev_init(dldwd_priv_t *dev)
+{
+ struct net_device *ndev = &dev->ndev;
+
+ dev->dir_dev = NULL;
+ /* create the directory for it to sit in */
+ dev->dir_dev = create_proc_entry(ndev->name, S_IFDIR | S_IRUGO | S_IXUGO,
+ dir_base);
+ if (dev->dir_dev == NULL) {
+ printk(KERN_ERR "Unable to initialise /proc/hermes/%s.\n", ndev->name);
+ goto fail;
+ }
+
+ dev->dir_regs = NULL;
+ dev->dir_regs = create_proc_read_entry("regs", S_IFREG | S_IRUGO,
+ dev->dir_dev, dldwd_proc_get_hermes_regs, dev);
+ if (dev->dir_regs == NULL) {
+ printk(KERN_ERR "Unable to initialise /proc/hermes/%s/regs.\n", ndev->name);
+ goto fail;
+ }
+
+ dev->dir_recs = NULL;
+ dev->dir_recs = create_proc_read_entry("recs", S_IFREG | S_IRUGO,
+ dev->dir_dev, dldwd_proc_get_hermes_recs, dev);
+ if (dev->dir_recs == NULL) {
+ printk(KERN_ERR "Unable to initialise /proc/hermes/%s/recs.\n", ndev->name);
+ goto fail;
+ }
+
+ return 0;
+ fail:
+ dldwd_proc_dev_cleanup(dev);
+ return -ENOMEM;
+}
+
+void
+dldwd_proc_dev_cleanup(dldwd_priv_t *priv)
+{
+ struct net_device *ndev = &priv->ndev;
+
+ if (priv->dir_regs) {
+ remove_proc_entry("regs", priv->dir_dev);
+ priv->dir_regs = NULL;
+ }
+ if (priv->dir_recs) {
+ remove_proc_entry("recs", priv->dir_dev);
+ priv->dir_recs = NULL;
+ }
+ if (priv->dir_dev) {
+ remove_proc_entry(ndev->name, dir_base);
+ priv->dir_dev = NULL;
+ }
+}
+
+static void
+dldwd_proc_cleanup(void)
+{
+ TRACE_ENTER("dldwd");
+
+ if (dir_base) {
+ remove_proc_entry("hermes", &proc_root);
+ dir_base = NULL;
+ }
+
+ TRACE_EXIT("dldwd");
+}
+
+int
+dldwd_setup(dldwd_priv_t* priv)
+{
+ struct net_device *ndev = &priv->ndev;;
+
+ spin_lock_init(&priv->lock);
+
+ /* Set up the net_device */
+ ether_setup(ndev);
+ ndev->priv = priv;
+
+ /* Setup up default routines */
+ ndev->init = dldwd_init;
+ ndev->open = NULL; /* Caller *must* override */
+ ndev->stop = NULL;
+ ndev->hard_start_xmit = dldwd_xmit;
+ ndev->tx_timeout = dldwd_tx_timeout;
+ ndev->watchdog_timeo = 4*HZ; /* 4 second timeout */
+
+ ndev->get_stats = dldwd_get_stats;
+ ndev->get_wireless_stats = dldwd_get_wireless_stats;
+
+ ndev->do_ioctl = dldwd_ioctl;
+
+ ndev->change_mtu = dldwd_change_mtu;
+ ndev->set_multicast_list = dldwd_set_multicast_list;
+
+ netif_stop_queue(ndev);
+
+ return 0;
+}
+
+#ifdef ORINOCO_DEBUG
+EXPORT_SYMBOL(dldwd_debug);
+#endif
+EXPORT_SYMBOL(dldwd_init);
+EXPORT_SYMBOL(dldwd_xmit);
+EXPORT_SYMBOL(dldwd_tx_timeout);
+EXPORT_SYMBOL(dldwd_ioctl);
+EXPORT_SYMBOL(dldwd_change_mtu);
+EXPORT_SYMBOL(dldwd_set_multicast_list);
+EXPORT_SYMBOL(dldwd_shutdown);
+EXPORT_SYMBOL(dldwd_reset);
+EXPORT_SYMBOL(dldwd_setup);
+EXPORT_SYMBOL(dldwd_proc_dev_init);
+EXPORT_SYMBOL(dldwd_proc_dev_cleanup);
+EXPORT_SYMBOL(dldwd_interrupt);
+
+static int __init init_dldwd(void)
+{
+ int err;
+
+ err = dldwd_proc_init();
+
+ printk(KERN_INFO "%s\n", version);
+
+ return 0;
+}
+
+static void __exit exit_dldwd(void)
+{
+ dldwd_proc_cleanup();
+}
+
+module_init(init_dldwd);
+module_exit(exit_dldwd);
FUNET's LINUX-ADM group, linux-adm@nic.funet.fi
TCL-scripts by Sam Shen (who was at: slshen@lbl.gov)